- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT5VJE9Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT5VJE9Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 117/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCT5VJE9Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁當前第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
117
www.national.com
21.0
Analog Comparators
The Dual Analog Comparator (ACMP2) module contains two
independent analog comparators with all necessary control
logic. Each comparator unit compares the analog input volt-
ages applied to two input pins and determines which voltage
is higher. The comparison results can be placed on two out-
put pins and/or read by the software from a register.
Figure 73 is a block diagram of the Dual Analog Comparator
module.
The two comparators are designated Comparator 1 (CMP1)
and Comparator 2 (CMP2). Each comparator has a positive
and a negative input, called CMP1P and CMP1N for Com-
parator 1 and CMP2P and CMP2N for Comparator 2. An op-
tional output, CMP1O for Comparator 1 or CMP2O for
Comparator 2, allows the external hardware to read the com-
parison results. If the positive input is greater than the nega-
tive input, the result is a logic 1. Otherwise, the result is a
logic 0. These same results are available to the software by
reading the CMPCTRL register. CMP1OP and CMP2OP are
the direct outputs of the analog comparator. These signals
are connected to the channels of the Multi-Wake-Up module.
21.1
ANALOG COMPARATOR CONTROL/
STATUS REGISTER (CMPCTRL)
The CMPCTRL register is a byte-wide, read/write register
that controls the comparator module and contains the com-
parison results. The control bits are read/write bits and the re-
sult bits are read-only bits. This register is cleared upon
reset. The register format is shown below.
CMP1RD
Comparator 1 Read. This read-only bit con-
tains the output of Comparator 1 when the
comparator
is
enabled
CMP1RD is set to 1 when the voltage on
CMP1P is greater than the voltage on CMP1N.
This bit is always 0 when Comparator 1 is dis-
abled.
Comparator 2 Read. This read-only bit con-
tains the output of Comparator 2 when the
comparator
is
enabled
CMP2RD is set to 1 when the voltage on
CMP2P is greater than the voltage on CMP2N.
This bit is always 0 when Comparator 2 is dis-
abled.
Comparator 1 Enable. This read/write bit en-
ables (1) or disables (0) Comparator 1.
Comparator 2 Enable. This read/write bit en-
ables (1) or disables (0) Comparator 2.
Comparator 1 Output Enable. This read/write
bit, when set to 1, enables the use of the
CMP1O pin as the output of Comparator 1
when Comparator 1 is enabled (CMP1EN=1).
If Comparator 1 is disabled (CMP1EN=0), set-
ting the CMP1OE bit results in a logic 0 on the
CMP1O output pin.
Comparator 2 Output Enable. This read/write
bit, when set to 1, enables the use of the
CMP2O pin as the output of Comparator 2
(CMP1EN=1).
CMP2RD
(CMP2EN=1).
CMP1EN
CMP2EN
CMP1OE
CMP2OE
when Comparator 2 is enabled (CMP2EN=1).
If Comparator 2 is disabled (CMP2EN=0), set-
ting the CMP2OE bit results in a logic 0 on the
CMP2O output pin.
21.2
The comparator I/O pins are alternate functions of the Port L
pins. In order for a comparator to operate, its two input pins
must be configured to operate as inputs in the alternate func-
tion mode.
Using a comparator's output pin is optional. If it is to be used,
it must be configured to operate as an output in the alternate
function mode. The comparison result bits in the CMPCTRL
register are available to the CPU whether or not the output
pin is enabled.
The comparators uses DC current whenever they are en-
abled. Therefore, in order to reduce power consumption, it is
recommended that the comparators be disabled when they
are not needed, especially before entering any of the Power
Save modes.
ANALOG COMPARATOR USAGE
7
6
5
4
3
2
1
0
Reserved CMP2OE CMP1OE CMP2EN CMP1EN CMP2RD CMP1RD
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT9 | |
| CR16HCT9VJE7 | Microcontroller |
| CR16HCT9VJE7Y | Microcontroller |
| CR16HCT9VJE8 | Microcontroller |
| CR16HCT9VJE8Y | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT5VJEXY | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9VJE7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。