- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT5VJE9Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT5VJE9Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 24/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCT5VJE9Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
24
program the prescaler value in advance and leave it un-
changed while a program or erase operation is in progress.
A similar (but separate) prescaler factor is applied to the EE-
PROM data memory. See Section 9.1.7 and Section 9.3.4 for
details.
9.1.6
Flash EEPROM Program Memory Control and
Status Register (FLCSR)
The Flash EEPROM Program Memory Control and Status
(FLCSR) register is a byte-wide, read/write register that con-
tains several status and control bits related to the program
memory. All reserved bits must be written with 0 for the mem-
ory to operate properly when writing to this register. Upon re-
set, this register is cleared to zero when the flash memory on
the chip is in the idle state.
The register format is shown below.
7
6
4
3
MERASE
Reserved
PMLFULL
PMER
Flash EEPROM Program Memory page erase.
When set (1) with MERASE bit cleared, a valid
write to the flash EEPROM program memory
erases the entire flash EEPROM program
memory page pointed to by the write address
rather than performing a write to the addressed
memory location.
Program Memory Busy. This bit is automatical-
ly set to 1 when the flash EEPROM program
memory is busy being programmed, and
cleared to 0 at all other times. (The MSTAT.PG-
MBUSY is also set to 1 whenever the PMBUSY
bit is set to 1.)
Program Memory Write-Latch Buffer Full.
When set (1), the double-buffered data register
for program memory write operations is full.
When cleared (0), the double-buffered data
register is not full.
Mass Erase Flash EEPROM Program Memory
Array. When set (1) in ISP or test mode, a valid
write to the flash EEPROM program memory
performs an erase to the whole flash EEPROM
program memory rather than perform a write to
the addressed memory location. However, it is
necessary to enter new values into the
FLERASE and FLEND registers to adjust the
mass erase timing before starting the mass
erase.
PMBUSY
PMLFULL
MERASE
9.1.7
Program Memory Timing Prescaler Register
(FLPSLR)
The FLPSLR register is a byte-wide, read/write register that
selects the prescaler divider ratio for the flash EEPROM pro-
gram memory programming clock. Before you program or
erase the program memory for the first time, you should pro-
gram the FLPSLR register with the proper prescaler value,
an 8-bit value called FTDIV. The device divides the system
clock by (FTDIV+1) to produce the program memory pro-
gramming clock.
You should choose a value of FTDIV to produce a clock of the
highest possible frequency that is equal to or just less than
200 kHz. For example, if the system clock frequency is 12.5
MHz, use the value 3E hex (62 decimal) for FTDIV, because
12.5 MHz / (62+1) = 198.4 kHz. Do not modify this register
while a flash EEPROM program or erase operation is in
progress.
Upon reset, this register is programmed by default with the
value 63 hex (99 decimal), which is an appropriate setting for
a 20 MHz system clock.
9.1.8
The FLSTART register is a byte-wide read/write register that
controls the program and erase start delay time. This value is
loaded into the lower 8 bits of the flash timing counter, and at
the same time, 00
2
is loaded into the upper 2 bits. Before you
program or erase the program memory for the first time, pro-
gram the FLSTART register with the proper prescaler value,
FTSTART. The flash timing counter generates a delay of
(FTSTART + 1) prescaler output clocks. The default value
provides a delay time of 10
ms
when the prescaler output
clock is 200kHz. Do not modify this register while a program
or erase operation is in progress.
Upon reset, this register resets to 01
16
when the flash mem-
ory on the chip is in an idle state.
Program Memory Start Time Reload (FLSTART)
9.1.9
Program Memory Transition Time Reload
Register (FLTRAN)
The FLTRAN register is a byte-wide read/write register that
controls some program/erase transition times. This value is
loaded into the lower 8 bits of the flash timing counter, and at
the same time, 00
2
is loaded into the upper 2 bits. Before you
program or erase the program memory for the first time, you
should program the FLTRAM register with the proper pres-
caler value, FTTRAN. The flash timing counter generates a
delay of (FTTRAN + 1) prescaler output clocks. The default
value provides a delay time of 5ms when the prescaler output
clock is 200kHz. Do not modify this register while a program
or erase operation is in progress.
Upon reset, this register resets to 00
16
when the flash mem-
ory on the chip is in an idle state.
9.1.10
Program Memory Programming Time Reload
Register (FLPROG)
The FLPROG register is a byte-wide read/write register that
controls the programming pulse width. This value is loaded
into the lower 8 bits of the flash timing counter, and at the
same time, 00
2
is loaded into the upper 2 bits. Before you
program or erase the program memory for the first time, pro-
gram the FLPROG register with the proper prescaler value,
FTPROG. The flash timing counter generates a programming
pulse width of (FTPROG + 1) prescaler output clocks. The
default value provides a delay time of 30ms when the pres-
caler output clock is 200kHz.
Do not modify this register while program/erase operation is
in progress.
Upon reset, this register resets to 05
16
when the flash mem-
ory on the chip is in idle state.
2
1
0
PMBUSY
PMER
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT9 | |
| CR16HCT9VJE7 | Microcontroller |
| CR16HCT9VJE7Y | Microcontroller |
| CR16HCT9VJE8 | Microcontroller |
| CR16HCT9VJE8Y | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT5VJEXY | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9VJE7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。