參數資料
型號： DTMFDECODER-RD
廠商： Silicon Laboratories Inc
文件頁數： 38/178頁
文件大?。?/td> 0K
描述： KIT REF DESIGN DTMF DECODER
應用說明： DTMF Decoder Ref Design AppNote
標準包裝： 1
主要目的： 電信，DTMF 解碼器
嵌入式： 否
已用 IC / 零件： C8051F300
主要屬性： 8kHz 采樣速率模數轉換器
次要屬性： 16 個 Goertzel 濾波器
已供物品： 板，軟件
產品目錄頁面： 627 (CN2011-ZH PDF)
相關產品： 336-1535-5-ND - IC 8051 MCU 8K FLASH 14-SOIC
C8051F300-GMR-ND - IC 8051 MCU 8K FLASH 11QFN
336-1245-ND - IC 8051 MCU 8K FLASH 11QFN
其它名稱： 336-1283
C8051F300/1/2/3/4/5
132
Rev. 2.9
14.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 14.2), which is not user
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
RX Timer
Start
Detected
Overflow
TH1
TL1
TX Clock
2
RX Clock
2
Timer 1
UART0
Figure 14.2. UART0 Baud Rate Logic
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see Section “15.1.3. Mode 2: 8-bit Coun-
ter/Timer with Auto-Reload” on page 145). The Timer 1 reload value should be set so that overflows will
occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of five
sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, or the external oscillator clock / 8. For any
given Timer 1 clock source, the UART0 baud rate is determined by Equation 14.1.
UartBaudRate
T1
CLK
256
T1H
–
-------------------------------
1
2
---
=
Equation 14.1. UART0 Baud Rate
Where T1CLK is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
value). Timer 1 clock frequency is selected as described in Section “15.2. Timer 2” on page 151. A quick
reference for typical baud rates and system clock frequencies is given in Tables 14.1 through 14.6. Note
that the internal oscillator may still generate the system clock when the external oscillator is driving Timer 1
相關PDF資料
PDF描述
UPZ2E121MND9 CAP ALUM 120UF 250V 20% RADIAL
A3KKB-1036M IDC CABLE - APK10B/AE10M/APK10B
UVR2G101MRD6 CAP ALUM 100UF 400V 20% RADIAL
LLS2A102MELZ CAP ALUM 1000UF 100V 20% SNAP
SI5310-EVB BOARD EVALUATION FOR SI5310
相關代理商/技術參數
參數描述
DTMG5812L WAF 制造商:ON Semiconductor 功能描述:
DTMG5852L WAF 制造商:ON Semiconductor 功能描述:
DTMH04-2PA 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP A KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, A KEY, 2WAY, Series:DTMH, No. of Positions:2, Gender:Receptacle, No. of Rows:1 , RoHS Compliant: Yes
DTMH04-2PB 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP B KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, B KEY, 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, B KEY, 2WAY; Series:DTMH; Gender:Receptacle; No. of Contacts:2; No. of Rows:1; Contact Gender:Pin; Connector Mounting:Cable; Connector Shell Size:-; Contact Termination:Crimp; Contact Material:Copper; Contact;RoHS Compliant: Yes
DTMH04-2PC 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP C KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, C KEY, 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, C KEY, 2WAY; Series:DTMH; Gender:Receptacle; No. of Contacts:2; No. of Rows:1; Contact Gender:Pin; Connector Mounting:Cable; Connector Shell Size:-; Contact Termination:Crimp; Contact Material:Copper; Contact;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*