參數資料
型號： K4T1G044QQ-HC(L)E6
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： 1Gb Q-die DDR2 SDRAM Specification
中文描述： 1Gb的調Q DDR2內存芯片規格
文件頁數： 9/44頁
文件大?。?/td> 891K
代理商： K4T1G044QQ-HC(L)E6
K4T1G084QQ
K4T1G164QQ
Rev. 1.01 November 2007
DDR2 SDRAM
9 of 44
K4T1G044QQ
Symbol
Type
Function
CK, CK
Input
Clock:
CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of the
positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK (both
directions of crossing).
CKE
Input
Clock Enable:
CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and out-
put drivers. Taking CKE Low provides Precharge Power-Down and Self Refresh operation (all banks idle), or Active
Power-Down (row Active in any bank). CKE is synchronous for power down entry and exit, and for self refresh entry.
CKE is asynchronous for self refresh exit. After V
REF
has become stable during the power on and initialization
swquence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh entry and exit, V
REF
must be maintained to this input. CKE must be maintained high throughout read and write accesses. Input buffers,
excluding CK, CK, ODT and CKE are disabled during power-down. Input buffers, excluding CKE, are disabled during
self refresh.
CS
Input
Chip Select:
All commands are masked when CS is registered HIGH. CS provides for external Rank selection on sys-
tems with multiple Ranks. CS is considered part of the command code.
ODT
Input
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM. When
enabled, ODT is only applied to each DQ, DQS, DQS, RDQS, RDQS, and DM signal for x4/x8 configurations. For x16
configuration ODT is applied to each DQ, UDQS/UDQS, LDQS/LDQS, UDM, and LDM signal. The ODT pin will be
ignored if the Extended Mode Register (EMRS(1)) is programmed to disable ODT.
RAS, CAS, WE
Input
Command Inputs:
RAS, CAS and WE (along with CS) define the command being entered.
DM
Input
Input Data Mask:
DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coinci-
dent with that input data during a Write access. DM is sampled on both edges of DQS. Although DM pins are input only,
the DM loading matches the DQ and DQS loading. For x8 device, the function of DM or RDQS/RDQS is enabled by
EMRS command.
BA0 - BA2
Input
Bank Address Inputs:
BA0, BA1 and BA2 define to which bank an Active, Read, Write or Precharge command is
being applied. Bank address also determines if the mode register or extended mode register is to be accessed during
a MRS or EMRS cycle.
A0 - A13
Input
Address Inputs:
Provided the row address for Active commands and the column address and Auto Precharge bit for
Read/Write commands to select one location out of the memory array in the respective bank. A10 is sampled during a
Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If
only one bank is to be precharged, the bank is selected by BA0, BA1. The address inputs also provide the op-code dur-
ing Mode Register Set commands.
DQ
Input/Out-
put
Data Input/ Output:
Bi-directional data bus.
DQS, (DQS)
(LDQS), (LDQS)
(UDQS), (UDQS)
(RDQS), (RDQS)
Input/Out-
put
Data Strobe:
output with read data, input with write data. Edge-aligned with read data, centered in write data. For the
x16, LDQS corresponds to the data on DQ0-DQ7; UDQS corresponds to the data on DQ8-DQ15. For the x8, an RDQS
option using DM pin can be enabled via the EMRS(1) to simplify read timing. The data strobes DQS, LDQS, UDQS,
and RDQS may be used in single ended mode or paired with optional complementary signals DQS, LDQS, UDQS, and
RDQS to provide differential pair signaling to the system during both reads and writes. An EMRS(1) control bit enables
or disables all complementary data strobe signals.
In this data sheet, "differential DQS signals" refers to any of the following with A10 = 0 of EMRS(1)
x4 DQS/DQS
x8 DQS/DQS
if EMRS(1)[A11] = 0
x8 DQS/DQS, RDQS/RDQS,
if EMRS(1)[A11] = 1
x16 LDQS/LDQS and UDQS/UDQS
"single-ended DQS signals" refers to any of the following with A10 = 1 of EMRS(1)
x4 DQS
x8 DQS if EMRS(1)[A11] = 0
x8 DQS, RDQS, if EMRS(1)[A11] = 1
x16 LDQS and UDQS
NC
No Connect:
No internal electrical connection is present.
V
DD
/V
DDQ
Supply
Power Supply:
1.8V +/- 0.1V,
DQ Power Supply:
1.8V +/- 0.1V
V
SS
/V
SSQ
Supply
Ground
,
DQ Ground
V
DDL
Supply
DLL Power Supply:
1.8V +/- 0.1V
V
SSDL
Supply
DLL Ground
V
REF
Supply
Reference voltage
4.0 Input/Output Functional Description
相關PDF資料
PDF描述
K4T1G044QQ-HC(L)E7 1Gb Q-die DDR2 SDRAM Specification
K4T1G044QQ-HC(L)F7 1Gb Q-die DDR2 SDRAM Specification
K4T1G084QQ 1Gb Q-die DDR2 SDRAM Specification
K4T1G084QQ-HC(L)E6 1Gb Q-die DDR2 SDRAM Specification
K4T1G084QQ-HC(L)E7 1Gb Q-die DDR2 SDRAM Specification
相關代理商/技術參數
參數描述
K4T1G044QQ-HCLE7 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb Q-die DDR2 SDRAM Specification
K4T1G044QQ-HCLF7 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb Q-die DDR2 SDRAM Specification
K4T1G084QAZCD5 制造商:Samsung Semiconductor 功能描述:
K4T1G084QA-ZCD5 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb A-die DDR2 SDRAM Specification
K4T1G084QA-ZCE6 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb A-die DDR2 SDRAM Specification
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*