- 您現在的位置：買賣IC網 > PDF目錄377973 > ML9050 (OKI SEMICONDUCTOR CO., LTD.) 132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays PDF資料下載
參數資料
| 型號： | ML9050 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | 132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays |
| 中文描述： | 132通道液晶內置液晶點陣顯示RAM的驅動程序 |
| 文件頁數： | 35/71頁 |
| 文件大?。?/td> | 472K |
| 代理商： | ML9050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Semiconductor
ML9050/9051
35/71
PEDL9050-02
Electronic potentiometer register set (Write)
By setting a 6-bit data in the electronic potentiometer register using this command, it is possible
to set the LCD drive voltage V1 to one of the 64 voltage levels.
The electronic potentiometer mode is released after some data has been set in the electronic
potentiometer register using this command.
D7
*
D6
*
D5
0
0
0
.
D4
0
0
0
.
D3
0
0
0
.
D2
0
0
0
.
V1
D0
1
0
1
.
Small
Large
A0
0
1
1
1
1
1
1
1
1
0
1
.
D1
0
1
1
.
1
1
*:
Invalid bit
Set the data (*, *, 1, 0, 0, 0, 0, 0) when not using the electronic potentiometer function.
Sequence of setting the electronic potentiometer register:
Static indicator (2-Byte command)
This command is used for controlling the static drive type indicator display.
Static indicator display is controlled only by this command and is independent of all other
display control commands. One of the electrodes for driving the static indicator LCD is
connected to the pin FR and the other pin is connected to the pin FRS. It is recommended to place
the wiring pattern for the electrodes for static indicators far from those of the electrodes for
dynamic drive. If these interconnection patterns are too close to each other, they may cause
deterioration of the LCD device and the electrodes.
Since the Static indicator ON command is a two-byte command used in combination with the
static indictor register set command, these two commands should always be used together.
(The Static indicator OFF command is a single byte command.)
Electronic potentiometer mode set
Electronic potentiometer register set
End of modification
Yes
No
The electronic potentiometer mode is released
相關PDF資料 |
PDF描述 |
|---|---|
| ML9051 | 132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays |
| ML9060 | 1/2 DUTY, 160-OUTPUT STATIC LCD DRIVER |
| ML9090-01 | LCD Driver with Key Scanner and RAM(帶鍵掃描和RAM的LCD驅動器) |
| ML9090-02 | LCD Driver with Key Scanner and RAM(帶鍵掃描和RAM的LCD驅動器) |
| ML9092-01 | LCD Driver with Key Scanner and RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML9051 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays |
| ML9051G | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays |
| ML9055A | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Controller/Driver |
| ML9055A-02 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Controller/Driver |
| ML9055A-02DVVAZ01L | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Controller/Driver |
發布緊急采購，3分鐘左右您將得到回復。