- 您現在的位置：買賣IC網 > PDF目錄371179 > T7121-EL2 T7121 HDLC Interface for ISDN PDF資料下載
參數資料
| 型號： | T7121-EL2 |
| 英文描述： | T7121 HDLC Interface for ISDN |
| 中文描述： | T7121的HDLC接口用于ISDN |
| 文件頁數： | 35/68頁 |
| 文件大小： | 685K |
| 代理商： | T7121-EL2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Lucent Technologies Inc.
35
Data Sheet
April 1997
T7121 HDLC Interface for ISDN (HIFI-64)
Functional Description
(continued)
* RLOOP and LLOOP should not be set to 1 simultaneously.
Setting RRES and TRES simultaneously returns the registers to their default values without causing the outputs to 3-state.
Table 13. Register R6—Operation Control Register
R6—B7
PDWN
(0)
R6—B6
3STATE
(0)
R6—B5
TRES
(0)
R6—B4
RRES
(0)
R6—B3
ENT
(0)
R6—B2
ENR
(0)
R6—B1
LLOOP
(0)
R6—B0
RLOOP
(0)
Register
R6
Bit
B0*
Symbol
RLOOP
Name/Function
Remote Loopback.
Setting this bit to 1 loops the received data back to
the distant end. When this bit is 0, normal transmission occurs.
Local Loopback.
Setting this bit to 1 loops transmitted data to the inter-
nal receiver. The receive data pin input (either DRA or DRB) is ignored.
Clearing this bit to 0 allows normal transmission.
Enable Receiver.
When this bit is set to 1, the received data is pro-
cessed by the receiver. When this bit is cleared to 0, incoming data is
ignored.
Enable Transmitter.
When this bit is set to 1, the transmitter is enabled,
and user data is transmitted on the selected transmit data pin(s). If no
transmit data pin is selected, the transmitter empties while the output
pins are 3-stated. When this bit is cleared to 0, the transmitter is dis-
abled. See Table 3.
Receiver Reset.
Write only. Setting this bit to 1 generates an internal
pulse that resets the HDLC receiver. The receive FIFO and related sta-
tus bits are cleared. The REOF, RF, RIDLE, and OVERRUN interrupts
are cleared. The receiver is placed in a known state.
Transmitter Reset.
Write only. Setting this bit to 1 generates an internal
pulse that resets the HDLC transmitter. The transmit FIFO's status bits
are initialized and the transmitter enters a known state. The UNDABT
interrupt is cleared and the TE interrupt is set. TDONE is cleared in
HDLC mode and set in transparent mode.
3STATE.
This bit places all HIFI-64 outputs into a high-impedance (3-
state) state. This state lasts until both
CS
and
RD
are detected low simul-
taneously.
Powerdown.
Setting this bit to 1 places the HIFI-64 into a low-power
mode. This has the effect of stopping the internal data clock and results
in significantly reduced power dissipation.
R6
B1*
LLOOP
R6
B2
ENR
R6
B3
ENT
R6
B4
RRES
R6
B5
TRES
R6
B6
3STATE
R6
B7
PDWN
相關PDF資料 |
PDF描述 |
|---|---|
| T7121-PL2 | T7121 HDLC Interface for ISDN |
| T7121 | HDLC Interface for ISDN (HIFI-64)(應用于ISDN的HDLC（高階數據鏈路）接口) |
| T7502 | T7502 Dual PCM Codec with Filters |
| T7503 | T7503 Dual PCM Codec with Filters |
| T7504 | T7504 and T75504 Quad PCM Codecs with Filters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7-121F1 | 功能描述:撥動開關 ON OFF ON 1 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-121F5 | 功能描述:撥動開關 ON OFF ON 1 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-121G1 | 功能描述:撥動開關 (ON) OFF ON 1 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-121G5 | 功能描述:撥動開關 (ON) OFF ON 1 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-121H1 | 制造商:OTTO 功能描述:Toggle Switches OFF NONE ON 1 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:TOGGLE SWITCH 1 POLE |
發布緊急采購，3分鐘左右您將得到回復。