- 您現在的位置：買賣IC網 > PDF目錄2121 > XRT83SL30IV-F (Exar Corporation)IC LIU T1/E1/J1 SGL 64TQFP PDF資料下載
參數資料
| 型號： | XRT83SL30IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 10/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 SGL 64TQFP |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83SL30
15
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
NLCDE1
NLCDE0
33
34
I
Network Loop Code Detection Enable pin 1
Network Loop Code Detection Enable pin 0
In Hardware Mode, NLCDE[1:0] pins are used to control the Loop-Code
detection according to the following table:
When NLCDE1=”0” and NCLDE0=”1”, or NLCDE1=”1” and NLCDE0=”0”, the
chip is manually programed to monitor the receive data for the Loop-Up or
Loop-Down code respectively. When the presence of the “00001” or “001”
pattern is detected for more than 5 seconds, the NLCD pin is set to “1” and
the Host has the option to activate the loop-back function manually.
Setting the NLCDE1=”1” and NLCDE0=”1” enables the Automatic Loop-
Code detection and Remote-Loop-Back activation mode. As this mode is ini-
tiated, the state of the NLCD pin is reset to “0” and the chip is programmed to
monitor the receive data for the Loop-Up Code. If the “00001” pattern is
detected for longer than 5 seconds, the NLCD pin is set to “1”, Remote Loop-
Back is activated and the chip is automatically programed to monitor the
receive data for the Loop-Down code. The NLCD pin stays “High” even after
the chip stops receiving the Loop-Up code. The remote Loop-Back condition
is removed when the chip receives the Loop-Down code for more than 5 sec-
onds or if the Automatic Loop-Code detection mode is terminated.
INSBPV
35
I
Insert Bipolar Violation
In Hardware Mode, when this pin transitions from "0" to "1", a bipolar viola-
tion is inserted in the transmitted data stream. Bipolar violation can be
inserted either in the QRSS pattern, or input data when operating in single-
rail mode. The state of this pin is sampled on the rising edge of TCLK.
NOTE: To ensure the insertion of a bipolar violation, this pin should be reset
to a "0" prior to setting to a "1".
ALARM FUNCTION/OTHER
SIGNAL NAME
PIN #TYPE
DESCRIPTION
NLCDE1
NLCDE0
Function
0
Disable Loop-Code
Detection
0
1
Detect Loop-Up Code in
Receive Data
1
Automatic Loop-Code
Detection
1
0
Detect Loop-Down Code in
Receive Data
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL314IB-L | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83SL34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
| XRT83SL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VSH28IB | IC LIU SH E1 OCTAL 225BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL30IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314ES | 功能描述:LIN 收發器 14 CHT1/E1 LIUSH RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT83SL314IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。