- 您現在的位置：買賣IC網 > PDF目錄2121 > XRT83SL30IV-F (Exar Corporation)IC LIU T1/E1/J1 SGL 64TQFP PDF資料下載
參數資料
| 型號： | XRT83SL30IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 52/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 SGL 64TQFP |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83SL30
53
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
D3
NLCD
Network Loop-Code Detection:
This bit operates differently in the Manual or the Automatic Net-
work Loop-Code detection modes.
In the Manual Loop-Code detection mode (NLCDE1 =”0” and
NLCDE0 =”1”, or NLCDE1 =”1” and NLCDE0 =”0”) this bit gets
set to “1” as soon as the Loop-Up (“00001”) or Loop-Down
(“001”) code is detected in the receive data for longer than 5 sec-
onds. The NLCD bit stays in the “1” state for as long as the chip
detects the presence of the Loop-Code in the receive data and it
is reset to “0” as soon as it stops receiving it. In this mode if the
NLCD interrupt is enabled the chip will initiate an interrupt on
every transition of the NLCD.
When the Automatic Loop-Code detection mode (NLCDE1 =”1”
and NLCDE0 =”1”) is initiated, the state of the NLCD interface bit
is reset to “0” and the chip is programmed to monitor the receive
input data for the Loop-Up Code. This bit is set to a “1” to indicate
that the Network Loop Code is detected for more than 5 sec-
onds. Simultaneously the Remote Loop-Back condition is auto-
matically activated and the chip is programmed to monitor the
receive data for the Network Loop-Down Code. The NLCD bit
stays in the “1” state for as long as the Remote Loop-Back condi-
tion is in effect even if the chip stops receiving the Loop-Up
Code. Remote Loop-Back is removed if the chip detects the
“001” pattern for longer than 5 seconds in the receive data.
Detecting the “001” pattern also results in resetting the NLCD
interface bit and initiating an interrupt provided the NLCD inter-
rupt enable bit it active. When programmed in the Automatic
detection mode, the NLCD interface bit stays “High” for the entire
time the Remote Loop-Back is active and initiates an interrupt
anytime the status of the NLCD bit changes. In this mode the
host can monitor the state of the NLCD bit to determine if the
Remote Loop-Back is activated.
RO
0
D2
AISD
Alarm Indication Signal Detect:
This bit is set to a "1" to indi-
cate All Ones Signal is detected by the receiver. The value of this
bit is based on the current status of Alarm Indication Signal
detector. If the AISDIE bit is enabled, any transition on this bit will
generate an Interrupt.
RO
0
D1
RLOS
Receive Loss of Signal:
This bit is set to a "1" to indicate that
the receive input signal is lost. The value of this bit is based on
the current status of the receive input signal. If the RLOSIE bit is
enabled, any transition on this bit will generate an Interrupt.
RO
0
D0
QRPD
Quasi-random Pattern Detection:
This bit is set to a "1" to indi-
cate the receiver is currently in synchronization with QRSS pat-
tern. The value of this bit is based on the current status of Quasi-
random pattern detector of. If the QRPDIE bit is enabled, any
transition on this bit will generate an Interrupt.
RO
0
TABLE 23: MICROPROCESSOR REGISTER #5 BIT DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL314IB-L | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83SL34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
| XRT83SL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VSH28IB | IC LIU SH E1 OCTAL 225BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL30IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314ES | 功能描述:LIN 收發器 14 CHT1/E1 LIUSH RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT83SL314IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。