3802 GROUP USER'S MANUAL
3-3
APPENDIX
3.1 Electrical characteristics
When STP instruction
is executed with clock
stopped, output
transistors isolated.
Note 1: P45 is measured when the P45/TXD P-channel output disable bit of the UART control register (bit 4 of address 001B16) is “0”.
P51 is measured when the P51/SOUT2 P-channel output disable bit of the serial I/O2 control register (bit 7 of address 001D16) is “0”.
2: With output transistors isolated and A-D converter having completed conversion, and not including current flowing through VREF pin.
2.0
1.0
5.0
–5.0
5.5
13
8
2.0
1
10
“H” output voltage P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
P60–P67 (Note 1)
“L” output voltage
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47,P50–P57,
P60–P67
Hysteresis
CNTR0, CNTR1, INT0–INT4
Hysteresis
RXD, SCLK1, SIN2, SCLK2
Hysteresis
RESET
“H” input current
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
P60–P67
“H” input current
RESET, CNVSS
“H” input current
XIN
“L” input current
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
P60–P67, RESET, CNVSS
“L” input current
RESET, CNVSS
“L” input current
XIN
RAM hold voltage
Symbol
Parameter
Limits
Min.
V
Unit
VCC–2.0
VCC–1.0
0.4
0.5
4
–4
6.4
4
0.8
1.5
1
0.2
0.1
Typ.
Max.
IOH = –10 mA
VCC = 4.0 to 5.5 V
IOH = –1.0 mA
VCC = 3.0 to 5.5 V
IOL = 10 mA
VCC = 4.0 to 5.5 V
IOL = 1.0 mA
VCC = 3.0 to 5.5 V
VI = VCC
VI = VSS
When clock stopped
f(XIN) = 8 MHz, VCC = 5 V
f(XIN) = 5 MHz, VCC = 5 V
f(XIN) = 2 MHz, VCC = 3 V
Ta = 25
°C
(Note 2)
Ta = 85
°C
(Note 2)
2.0
Test conditions
VT+ – VT–
IIH
IIL
VRAM
VOH
VOL
ICC
V
A
V
mA
A
Power source current
When WIT instruction is executed with
f(Xin) = 8MHz,VCC=5V
When WIT instruction is executed with
f(Xin) = 5MHz,VCC=5V
When WIT instruction is executed with
f(Xin) = 2MHz,VCC=3V
8
±2.5
50
200
5.0
Limits
Min.
Bits
LSB
tC(
φ)
k
A
Typ.
Max.
±1
35
150
0.5
Note: When D-A conversion registers (addresses 003616 and 003716) contain “0016”.
Resolution
Absolute accuracy (excluding quantization error)
Conversion time
Ladder resistor
Reference power source input current (Note)
A-D port input current
—
tCONV
RLADDER
IVREF
II(AD)
Symbol
Parameter
Unit
VREF = 5.0 V
50
Table 3.1.3 ELECTRICAL CHARACTERISTICS (VCC = 3.0 to 5.5 V, VSS = 0 V, Ta = –20 to 85
°C, unless otherwise noted)
Test conditions
Table 3.1.4 A–D CONVERTER CHARACTERISTICS
(VCC = 3.0 to 5.5 V, VSS = AVSS = 0 V, VREF = 2.0 V to VCC, Ta = –20 to 85
°C, unless otherwise noted)
3.1.3 Electrical characteristics
3.1.4 A-D converter characteristics