- 您現在的位置：買賣IC網 > PDF目錄16537 > AD9558/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9558 PDF資料下載
參數資料
| 型號： | AD9558/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/104頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD9558 |
| 產品變化通告： | AD9558 Minor Metal Mask Change 17/Apr/2012 |
| 設計資源： | AD9558 Eval Brd BOM AD9558 Schematic |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
AD9558
Data Sheet
Rev. B | Page 26 of 104
GETTING STARTED
CHIP POWER MONITOR AND STARTUP
The AD9558 monitors the voltage on the power supplies at
power-up. When DVDD3 is greater than 2.35 V ± 0.1 V and
DVDD and AVDD are greater than 1.4 V ± 0.05 V, the device
generates a 20 ms reset pulse. The power-up reset pulse is internal
and independent of the
A
RESETE
A
pin. This internal power-up reset
sequence eliminates the need for the user to provide external power
supply sequencing. Within 45 ns after the leading edge of the
internal reset pulse, the M7 to M0 multifunction pins behave
as high impedance digital inputs and continue to do so until
programmed otherwise. The delay on the M7 to M0 pin function
change is 45 ns for pin reset or soft reset.
During a device reset (either via the power-up reset pulse or the
A
RESETE
A
pin), the multifunction pins (M7 to M0) behave as high
impedance inputs, but upon removal of the reset condition,
level-sensitive latches capture the logic pattern present on the
multifunction pins.
MULTIFUNCTION PINS AT RESET/POWER-UP
The AD9558 requires the user to supply the desired logic state
to the PINCONTROL pin, as well as to the M7 to M0 pins. If
PINCONTROL is high, the part is in hard pin programming
mode. See the Pin Program Function Description section for
details on hard pin programming.
At startup, there are three choices for the M7 to M0 pins: pull-
up, pull-down, and floating. If the PINCONTROL pin is low,
the M7 to M0 pins determine the following configurations:
Following a reset, the M1 and M0 pins determine whether
the serial port interface behaves according to the SPI or I2C
protocol. Specifically, M0 = M1 = low selects the SPI
interface, and any other value selects the I2C port. The 3-
level logic of M1 and M0 allows the user to select eight
The M3 and M2 pins select which of the eight possible
EEPROM profiles are loaded, or if the EEPROM loading is
bypassed. Leaving M3 and M2 floating at startup bypasses
the EEPROM loading, and the factory defaults are used
instead (see Table 22).
DEVICE REGISTER PROGRAMMING WHEN USING
A REGISTER SETUP FILE
The evaluation software contains a programming wizard and
a convenient graphical user interface that assists the user in
determining the optimal configuration for the DPLL, APLL,
and SYSCLK based on the desired input and output frequencies.
It generates a register setup file with a .STP extension that is
easily readable using a text editor.
After using the evaluation software to create the setup file, use
the following sequence to program the AD9557 once:
1. Register 0x0A01 = 0x20 (set user free run mode).
2. Register 0x0A02 = 0x02 (hold outputs in static SYNC).
(Skip this step if using SYNC on DPLL phase lock or SYNC
on DPLL frequency lock. See Register 0x0500[1:0].)
3. Register 0x0405 = 0x20 (clear APLL VCO calibration).
4. Write the register values in the STP file from Address 0x0000
to Address 0x032E.
5. Register 0x0005 = 0x01 (update all registers).
6. Write the rest of the registers in the STP file, starting at
Address 0x0400.
7. Register 0x0405 = 0x21 (calibrate APLLon next I/O update).
8. Register 0x0403 = 0x07 (configure APLL).
9. Register 0x0400 = 0x81 (configure APLL).
10. Register 0x0005 = 0x01 (update all registers).
11. Register 0x0A01[5] = 0b (clear user free run mode).
12. Register 0x0005 = 0x01 (update all registers).
REGISTER PROGRAMMING OVERVIEW
This section provides an overview of the register blocks in the
AD9558, describing what they do and why they are important.
Registers Differing from Defaults for Optimal Performance
Ensure that the following registers are programmed to the listed
values for optimal performance:
Register 0x0405[7:4] = 0x2
Register 0x0403 = 0x07
Register 0x0400 = 0x81
If the silicon revision (Register 0x000A) equals 0x21 or higher,
the values listed here are already the default values.
相關PDF資料 |
PDF描述 |
|---|---|
| GBM22DSAH | CONN EDGECARD 44POS R/A .156 SLD |
| DK-2632-03 | CABLE FIBER OPTIC DUAL LC-SC 3M |
| GEM30DTAS | CONN EDGECARD 60POS R/A .156 SLD |
| GMM12DRXI | CONN EDGECARD 24POS DIP .156 SLD |
| P1330R-105K | INDUCTOR POWER 1000.0UH SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9559 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator |
| AD9559/PCBZ | 功能描述:時鐘和定時器開發工具 Multi-protocol line card dual clock RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| AD9559BCPZ | 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| AD9559BCPZ-REEL7 | 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| AD9559PCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator |
發布緊急采購，3分鐘左右您將得到回復。