參數資料
型號： AD9558/PCBZ
廠商： Analog Devices Inc
文件頁數： 25/104頁
文件大小： 0K
描述： BOARD EVAL FOR AD9558
產品變化通告： AD9558 Minor Metal Mask Change 17/Apr/2012
設計資源： AD9558 Eval Brd BOM
AD9558 Schematic
標準包裝： 1
系列： *
Data Sheet
AD9558
Rev. B | Page 27 of 104
Program the System Clock and Free Run Tuning Word
The system clock multiplier (SYSCLK) parameters are at
Register 0x0100 to Register 0x0108, and the free run tuning
word is at Register 0x0300 to Register 0x0303. Use the following
steps for optimal performance:
1. Set the system clock PLL input type and divider values.
2. Set the system clock period.
It is essential to program the system clock period because
many of the AD9558 subsystems rely on this value.
3. Set the system clock stability timer.
It is highly recommended that the system clock stability
timer be programmed. This is especially important when
using the system clock multiplier and also applies when
using an external system clock source, especially if the
external source is not expected to be completely stable
when power is applied to the AD9558. The system clock
stability timer specifies the amount of time that the system
clock PLL must be locked before the part declares that the
system clock is stable. The default value is 50 ms.
4. Program the free run tuning word.
The free run frequency of the digital PLL (DPLL) determines
the frequency appearing at the APLL input when free run
mode is selected. The free run tuning word is at Register
0x0300 to Register 0x0303. The correct free run frequency
is required for the APLL to calibrate and lock correctly.
5. Set user free run mode (Register 0x0A01[5] = 1b).
Initialize and Calibrate the Output PLL (APLL)
The registers controlling the APLL are at Register 0x0400
to Register 0x0408. This low noise, integer-N PLL multiplies
the DPLL output (which is usually 175 MHz to 200 MHz) to a
frequency in the 3.35 GHz to 4.05 GHz range. After the system
clock is configured and the free run tuning word is set in
Register 0x0300 to Register 0x0303, the user can set the manual
APLL VCO calibration bit (Register 0x0405[0]) and issue an I/O
update (Register 0x0005[0]). This process performs the APLL
VCO calibration. VCO calibration ensures that, at the time of
calibration, the dc control voltage of the APLL VCO is centered in
the middle of its operating range. It is important to remember the
following points when calibrating the APLL VCO:
The system clock must be stable.
The APLL VCO must have the correct frequency from the
30-bit DCO (digitally controlled oscillator) during
calibration.
The APLL VCO must be recalibrated any time the APLL
frequency changes.
APLL VCO calibration occurs on the low-to-high transition
of the manual APLL VCO calibration bit, and this bit is not
autoclearing. Therefore, this bit must be cleared (and an I/O
update issued) before another APLL calibration is started.
The best way to monitor successful APLL calibration is to
monitor Bit 2 in Register 0x0D01 (APLL lock).
Program the Clock Distribution Outputs
The APLL output goes to the clock distribution block. The
clock distribution parameters reside in Register 0x0500 to
Register 0x0509. They include the following:
Output power-down control
Output enable (disabled by default)
Output synchronization
Output mode control
Output divider functionality
See the Clock Distribution section for more information.
Generate the Output Clock
If Register 0x0500[1:0] is programmed for automatic clock
distribution synchronization via the DPLL phase or frequency
lock, the synthesized output signal appears at the clock distribution
outputs. Otherwise, set and then clear the soft sync clock
distribution bit (Register 0x0A02, Bit 1), or use a multifunction
pin input (if programmed for use) to generate a clock
distribution sync pulse, which causes the synthesized output
signal to appear at the clock distribution outputs.
Program the Multifunction Pins (Optional)
This step is required only if the user intends to use any of the
multifunction pins for status or control. The multifunction pin
parameters are at Register 0x0200 to Register 0x0208.
Program the IRQ Functionality (Optional)
This step is required only if the user intends to use the IRQ feature.
The IRQ monitor registers are at Register 0x0D02 to Register
0x0D09. If the desired bits in the IRQ mask registers at Register
0x020A to Register 0x020F are set high, the appropriate IRQ
monitor bit at Register 0x0D02 to Register 0x0D07 is set high
when the indicated event occurs.
Individual IRQ events are cleared by using the IRQ clearing
registers at Register 0x0A04 to Register 0x0A09, or by setting
the clear all IRQs bit (Register 0x0A03[1]) to 1b.
The default values of the IRQ mask registers are such that
interrupts are not generated. The IRQ pin mode default is open-
drain NMOS.
Program the Watchdog Timer (Optional)
This step is required only if the user intends to use the watchdog
timer. The watchdog timer control is in Register 0x0210 and
Register 0x0211 and is disabled by default.
The watchdog timer is useful for generating an IRQ after a fixed
amount of time. The timer is reset by setting the clear watchdog
timer bit (Register 0x0A03[0]) to 1b.
相關PDF資料
PDF描述
GBM22DSAH CONN EDGECARD 44POS R/A .156 SLD
DK-2632-03 CABLE FIBER OPTIC DUAL LC-SC 3M
GEM30DTAS CONN EDGECARD 60POS R/A .156 SLD
GMM12DRXI CONN EDGECARD 24POS DIP .156 SLD
P1330R-105K INDUCTOR POWER 1000.0UH SMD
相關代理商/技術參數
參數描述
AD9559 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator
AD9559/PCBZ 功能描述:時鐘和定時器開發工具 Multi-protocol line card dual clock RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V
AD9559BCPZ 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
AD9559BCPZ-REEL7 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
AD9559PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*