參數資料
型號： COP8CCR9KMT8
廠商： National Semiconductor
文件頁數： 33/111頁
文件大小： 0K
描述： IC MCU EEPROM 8BIT 32K 56-TSSOP
標準包裝： 34
系列： COP8™ 8C
核心處理器： COP8
芯體尺寸： 8-位
速度： 20MHz
連通性： Microwire/Plus（SPI），UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 49
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 56-TFSOP（0.240"，6.10mm 寬）
包裝： 管件
其它名稱： *COP8CCR9KMT8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
Figure 5-3. Reset Circuit Using External Reset
5.7.2
On-Chip Brownout Reset
When enabled, the device generates an internal reset as VCC rises. While VCC is less than the specified
brownout voltage (Vbor), the device is held in the reset condition and the Idle Timer is preset with 00Fx
(240–256 tC). When VCC reaches a value greater than Vbor, the Idle Timer starts counting down. Upon
underflow of the Idle Timer, the internal reset is released and the device will start executing instructions.
This internal reset will perform the same functions as external reset. Once VCC is above the Vbor and this
initial Idle Timer time-out takes place, instruction execution begins and the Idle Timer can be used
normally. If, however, VCC drops below the selected Vbor, an internal reset is generated, and the Idle Timer
is preset with 00Fx. The device now waits until VCC is greater than Vbor and the countdown starts over.
When enabled, the functional operation of the device, at frequency, is ensured down to the Vbor level.
Figure 5-4. Brownout Reset Operation
One exception to the above is that the brownout circuit will insert a delay of approximately 3 ms on power
up or any time the VCC drops below a voltage of about 1.8V. The device will be held in Reset for the
duration of this delay before the Idle Timer starts counting the 240 to 256 tC. This delay starts as soon as
the VCC rises above the trigger voltage (approximately 1.8V). This behavior is shown in Figure 5-4.
In Case 1, VCC rises from 0V and the on-chip RESET is undefined until the supply is greater than
approximately 1.0V. At this time the brownout circuit becomes active and holds the device in RESET. As
the supply passes a level of about 1.8V, a delay of about 3 ms (td) is started and the Idle Timer is preset
to a value between 00F0 and 00FF (hex). Once VCC is greater than Vbor and td has expired, the Idle Timer
is allowed to count down (tid).
28
Functional Description
Copyright 2000–2013, Texas Instruments Incorporated
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
COP8SAA716M8/NOPB IC MCU OTP 8BIT 1K 16-SOIC
CP2101-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2103-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2104-F03-GM IC SGL USB-TO-UART BRIDGE 24QFN
CP2105-F01-GM IC SGL USB-DL UART BRIDGE 24QFN
相關代理商/技術參數
參數描述
COP8CCR9LVA7 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA7/63 制造商:Texas Instruments 功能描述:
COP8CCR9LVA7/63SN 功能描述:閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
COP8CCR9LVA7/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA763SN 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*