參數資料
型號: COP8CCR9KMT8
廠商: National Semiconductor
文件頁數: 88/111頁
文件大?。?/td> 0K
描述: IC MCU EEPROM 8BIT 32K 56-TSSOP
標準包裝: 34
系列: COP8™ 8C
核心處理器: COP8
芯體尺寸: 8-位
速度: 20MHz
連通性: Microwire/Plus(SPI),UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 49
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 16x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 56-TFSOP(0.240",6.10mm 寬)
包裝: 管件
其它名稱: *COP8CCR9KMT8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
Figure 5-24. VIS Operation
5.15.4 NON-MASKABLE INTERRUPT
5.15.4.1 Pending Flag
There is a pending flag bit associated with the non-maskable Software Trap interrupt, called STPND. This
pending flag is not memory-mapped and cannot be accessed directly by the software.
The pending flag is reset to zero when a device Reset occurs. When the non-maskable interrupt occurs,
the associated pending bit is set to 1. The interrupt service routine should contain an RPND instruction to
reset the pending flag to zero. The RPND instruction always resets the STPND flag.
5.15.4.2 Software Trap
The Software Trap is a special kind of non-maskable interrupt which occurs when the INTR instruction
(used to acknowledge interrupts) is fetched from program memory and placed in the instruction register.
This can happen in a variety of ways, usually because of an error condition. Some examples of causes
are listed below.
If the program counter incorrectly points to a memory location beyond the programmed Flash memory
space, the unused memory location returns zeros which is interpreted as the INTR instruction.
If the stack is popped beyond the allowed limit (address 06F Hex), a 7FFF will be loaded into the PC.
Since the Option Register resides at this location, and to maintain the integrity of the stack overpop
protection, the Flash memory will return a zero on an instruction fetch and a software trap will be
triggered.
A Software Trap can be triggered by a temporary hardware condition such as a brownout or power supply
glitch.
The Software Trap has the highest priority of all interrupts. When a Software Trap occurs, the STPND bit
is set. The GIE bit is not affected and the pending bit (not accessible by the user) is used to inhibit other
interrupts and to direct the program to the ST service routine with the VIS instruction. Nothing can interrupt
a Software Trap service routine except for another Software Trap. The STPND can be reset only by the
RPND instruction or a chip Reset.
78
Functional Description
Copyright 2000–2013, Texas Instruments Incorporated
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
COP8SAA716M8/NOPB IC MCU OTP 8BIT 1K 16-SOIC
CP2101-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2103-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2104-F03-GM IC SGL USB-TO-UART BRIDGE 24QFN
CP2105-F01-GM IC SGL USB-DL UART BRIDGE 24QFN
相關代理商/技術參數
參數描述
COP8CCR9LVA7 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA7/63 制造商:Texas Instruments 功能描述:
COP8CCR9LVA7/63SN 功能描述:閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
COP8CCR9LVA7/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA763SN 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC