- 您現在的位置：買賣IC網 > PDF目錄376727 > DK1241A (Electronic Theatre Controls, Inc.) Advanced Microstepping Motion Control Chipset PDF資料下載
參數資料
| 型號： | DK1241A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Microstepping Motion Control Chipset |
| 中文描述： | 高級微步運動控制芯片組 |
| 文件頁數： | 23/60頁 |
| 文件大?。?/td> | 422K |
| 代理商： | DK1241A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
23
consists of a bit mask, with 1 bit assigned to each axis. Executing this
command has the same affect as instantaneously switching to each
desired axes, and executing an UPDATE command.
Breakpoints
A breakpoint is a convenient way of programmng a profile or other
double-buffered parameter change upon some specific condition. There
are two types of breakpoints, those that have a 32-bit comparitor value
associated with themand those that do not. For those that have the
comparitor, a 32-bit comparitor value is loaded into the breakpoint
compare register first, and then one of the breakpoint conditions is
specified. For those breakpoint modes without associated comparitor
values only the breakpoint condition needs to be specified.
The double-buffered registers and commands will be updated upon
satisfaction of the specified breakpoint condition.
Here is a list of all of the available breakpoint conditions.
Positive
Target
Position Breakpoint
A 32 bit position breakpoint can be specified which will result in
the parameters being updated when the current target position
(the instantaneous desired axis position output fromthe profile
generator) equals or exceeds the specified breakpoint value. This
breakpoint is set using the SET_POS_BRK command.
Negative
Target
Position Breakpoint
A 32 bit position breakpoint can be specified which will result in
the parameters being updated when the current target position
(the instantaneous desired axis position output fromthe profile
generator) equals or is less than the specified breakpoint
value.This breakpoint is set using the SET_NEG_BRK command.
Positive
Actual
Position Breakpoint
A 32 bit position breakpoint can be specified which will result in
the parameters being updated when the current actual position
(the instantaneous position of the actual axis hardware) equals or
exceeds the specified breakpoint value.This breakpoint is set
using the SET_ACTL_POS_BRK command.
Negative
Actual
Position Breakpoint
A 32 bit position breakpoint can be specified which will result in
the parameters being updated when the current actual position
(the instantaneous position of the actual axis hardware) equals or
is less than the specified breakpoint value.This breakpoint is set
using the SET_ACTL_NEG_BRK command.
Time Breakpoint
A 32 bit time breakpoint can be specified which will result in the
parameters being updated when the #of cycles executed since
chip set reset (the current chip set time) is equal to the time
breakpoint value.The #of cycles continuously increases until it
rolls over from232 - 1 back to 0.The time breakpoint is set using
the SET_TIME_BRK command.
Motion Complete Breakpoint
A breakpoint can be specified which will result in the parameters
being updated when the previous motion has been completed
(motion complete bit is set). When using this breakpoint no 32 bit
compare value is required.
External Breakpoint
A breakpoint can be specified which will result in the parameters
being updated when the home signal of the corresponding axis
becomes active (low). When using this breakpoint no 32 bit
compare value is required. This breakpoint is useful whenever it is
desired that an external signal starts, stops, or otherwise modifies
the profile movement.
Normally, whenever one of these conditions has been programmed and
the condition occurs, the double-buffered parameters will automatically
be shifted to the active registers. There is a mechanismto disable this
"automatic update upon breakpoint" however. This is discussed in the
next section.
The above breakpoint modes are particularly useful during multi-axis
motion. This is because the next profile commands (set of host-
specified trajectory commands) can be pre-loaded and activated at the
precise position or time required, with no delay incurred to send an
update or load parameters command.
After a breakpoint condition has been satisfied it is no longer
active. To set up another breakpoint condition, a new one must be
explicitly set by the host.
The double-buffered registers that are shifted to the active
registers do not change upon being shifted, only the active
registers change.
Except for the MULTI_AXIS command, parameter loading and updating
is controlled individually for each axis. In addition each axis has a
separate 32-bit breakpoint register, and can be set to various individual
breakpoint conditions.
External Breakpoints and Homing
By connecting a home input sensor to the home signal input of the
MC1241-series chipsets it is possible to cause the chipset to halt a
motion at the moment it receives the home signal. This capability
makes it ideal for performng a home sequence. The following host I/O
sequence illustrates this:
GET_HOME
; check to make sure axis not already at
; home. If so, then a 'reverse' move must
; be made to retract axis fromhome switch.
; This ‘reversing’ sequence is not
; indicated here for simplicity sake
; load home move parameters
SET_POS 12345
SET_VEL 23456
SET_ACC 345
UPDATE
SET_EXT_BRK
; start home move
; initiate external breakpoint mode
相關PDF資料 |
PDF描述 |
|---|---|
| DK2100 | Navigator Motion Processor |
| DK3300 | Turbo uPSD DK3300 User Manual(Turbo系列 uPSD DK3300 用戶手冊) |
| DK60 | DIODY PROSTOWNICZE |
| DK61 | DIODY PROSTOWNICZE |
| DK62 | DIODY PROSTOWNICZE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DK125950 | 制造商:TE Connectivity 功能描述: |
| DK-125M-1 | 制造商:Luminus Devices 功能描述:EVAL BOARD & HEAT SINK FOR PT85/CBT85. MAX16818, 25A, 1 CH - Bulk |
| DK12GY | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
| DK12LG | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
| DK12S16 | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
發布緊急采購，3分鐘左右您將得到回復。