參數資料
型號: DS3112N
英文描述: RECT BRIDGE GPP 15A 600V GBJ
中文描述: 坦佩化T3/E3復用器3.3化T3/E3成幀器和M13/E13/G.747復用器
文件頁數: 92/135頁
文件大?。?/td> 585K
代理商: DS3112N
DS3112
92 of 135
Bit 1/Transmit Zero Stuffer Defeat (TZSD).
When this bit is set low, the HDLC will automatically
enable the zero stuffer in between the opening and closing flags of the HDLC message. When this bit is
set high, the device will not enable the zero stuffer under any condition.
0 = enable zero stuffer (normal operation)
1 = disable zero stuffer
Bit 2/Transmit CRC Invert (TCRCI).
When this bit is set low, the HDLC will allow the CRC to be
generated normally. When this bit is set high, the device will invert all 16 bits of the generated CRC. This
bit is ignored when the CRC generation is disabled (TCRCD = 1). This bit is useful in testing HDLC
operation.
0 = do not invert the generated CRC (normal operation)
1 = Invert the generated CRC
Bit 4/Transmit Flag/Idle Select (TFS).
This control bit determines whether flags or idle bytes will be
transmitted in between packets.
0 = 7Eh (flags)
1 = FFh (idle)
Bit 5/Transmit HDLC Reset (THR).
A zero to one transition will reset the Transmit HDLC controller.
Must be cleared and set again for a subsequent reset. A reset will flush the current contents of the transmit
FIFO and cause one FEh abort sequence (7 ones is a row) to be sent followed by either 7Eh (flags) or FFh
(idle) until a new packet is initiated by writing new data (at least 2 bytes) into the FIFO.
Bit 6/Receive HDLC Reset (RHR).
A zero to one transition will reset the Receive HDLC controller.
Must be cleared and set again for a subsequent reset. A reset will flush the current contents of the receive
FIFO and cause the receive HDLC controller to begin searching for a new incoming HDLC packet.
Bit 8/Transmit Invert Data (TID).
The control bit determines whether all of the data from the HDLC
controller (including flags and CRC checksum) will be inverted after processing.
0 = do not invert data (normal operation)
1 = invert all data
Bit 9/Receive Invert Data (RID).
The control bit determines whether all of the data into the HDLC
controller (including flags and CRC checksum) will be inverted before processing.
0 = do not invert data (normal operation)
1 = invert all data
Bits 10 to 12/Transmit Low Watermark Select Bits (TLWMS0 to TLWMS2).
These control bits
determine when the HDLC controller should set the TLWM status bit in the HDLC Status Register
(HSR). When the transmit FIFO contains less than the number of bytes configured by these bits, the
TLWM status bit will be set to a one.
相關PDF資料
PDF描述
DS3112RD RECT BRIDGE GPP 15A 800V GBJ
DS3134 Chateau Channelized T1 And E1 And HDLC Controller
DS3160 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
DS3171 Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers
DS3171N Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers
相關代理商/技術參數
參數描述
DS3112N+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112N+W 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112NC1 制造商:Maxim Integrated Products 功能描述:T3 E3 MULTIPLEXER, 3.3V T3/E3 FRAMER AND M13/E13/G.747 MUX - Rail/Tube
DS3112ND1E 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS3112RD 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray