- 您現在的位置：買賣IC網 > PDF目錄376976 > DS3112RD (Maxim Integrated Products, Inc.) RECT BRIDGE GPP 15A 800V GBJ PDF資料下載
參數資料
| 型號： | DS3112RD |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | RECT BRIDGE GPP 15A 800V GBJ |
| 中文描述： | DS3/E3多路復用器參考設計 |
| 文件頁數： | 21/135頁 |
| 文件大?。?/td> | 585K |
| 代理商： | DS3112RD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
DS3112
21 of 135
2.4 T3/E3 Transmit Formatter Signal Description
Signal Name:
FTSOF
Signal Description:
T3/E3 Transmit Formatter Start Of Frame Sync Signal
Signal Type:
Output/Input
This signal can be configured via the FTSOFC control bit in Master Control Register 1 to be either an
output or an input. When this signal is an output, it pulses for one FTCLK period to indicate a T3 or E3
frame boundary (Figure 2.4A). When this signal is an input, it is sampled to set the transmit T3 or E3
frame boundary (Figure 2.4A). This signal can be configured via the FTSOFI control bit in Master
Control Register 3 (Section 4.2) to be either active high (normal mode) or active low (inverted mode).
Signal Name:
FTCLK
Signal Description:
T3/E3 Transmit Formatter Clock
Signal Type:
Input
An accurate T3 (44.736MHz ±20ppm) or E3 (34.368MHz ±20ppm) clock should be applied at this signal.
This signal is used to clock data into the transmit T3/E3 formatter. Transmit data can be clocked into the
device either on a rising edge (normal mode) or a falling edge (inverted mode). This option is controlled
via the FTCLKI control bit in Master Control Register 3 (Section 4.2).
Signal Name:
FTD
Signal Description:
T3/E3 Transmit Formatter Serial Data
Signal Type:
Input
This signal inputs data into the transmit T3/E3 formatter. This signal can be sampled either on the rising
edge of FTCLK (normal mode) or the falling edge of FTCLK (inverted mode). This option is controlled
via the FTCLKI control bit in Master Control Register 3 (Section 4.2). Also, the data input to this signal
can be internally inverted if enabled via the FTDI control bit in Master Control Register 3 (Section 4.2).
When T3 C-Bit Parity Mode is disabled, C Bits are sampled at this input. This signal is ignored when the
M13/E13 multiplexer is enabled. (See the UNCHEN control bit in Master Control Register 1.) If not
used, this signal should be tied low.
Signal Name:
FTDEN
Signal Description:
T3/E3 Transmit Formatter Serial Data Enable or Gapped Clock Output
Signal Type:
Output
Via the DENMS control bit in Master Control Register 1, this signal can be configured to either output a
data enable or a gapped clock. In the data enable mode, this signal will go active when payload data
should be made available at the FTD input. In the gapped clock mode, this signal will act as a demand
clock for the FTD input and it will transition for each bit of payload data needed at the FTD input and it
will be suppressed when the transmit formatter inserts overhead data and hence no data is needed at the
FTD input. In the T3 Mode, overhead data is defined as the M Bits, F Bits, C Bits, X Bits, and P Bits. In
the E3 Mode, overhead data is defined as the FAS word, RAI Bit and Sn Bit (i.e., bits 1 to 12). See Figure
2.4A for an example. his signal can be internally inverted if enabled via the FTDENI control bit in
Master Control Register 3 (Section 4.2). This signal operates in the same manner even when the device is
configured in the Transmit Pass Through mode (see the TPT control bit in the T3/E3 Control Register).
相關PDF資料 |
PDF描述 |
|---|---|
| DS3134 | Chateau Channelized T1 And E1 And HDLC Controller |
| DS3160 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| DS3171 | Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers |
| DS3171N | Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers |
| DS3172 | Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3116MP000 | 制造商:Thomas & Betts 功能描述:MAXGARD - RR8F |
| DS311X | 功能描述:KWIK-CHG DESIGNATION STRIPS DBL RoHS:是 類別:盒，外殼，支架 >> 插線臺，插座面板 - 配件 系列:Kwik-Change® 標準包裝:50 系列:- 附件類型:模擬插頭，雙 樣式:耳機，0.173" 直徑 包括:- |
| DS312 | 功能描述:插線板 DESIGN STRIP COVER RoHS:否 制造商:Switchcraft 產品類型:Bantam (TT) 正規化: 高度/機架數量: 深度: 端接類型: 位置/觸點數量:48 |
| DS-312 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Four-Way Power Divider, 10 - 500 MHz |
| DS312_09 | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family: Introduction and Ordering Information |
發布緊急采購，3分鐘左右您將得到回復。