參數資料
型號： LH28F320S5H-L
廠商： Sharp Corporation
英文描述： 32M-BIT ( 2Mbit x16 / 4Mbit x8 )Boot Block Flash MEMORY(32M位( 2M位 x16 / 4M位 x8 )Boot Block 閃速存儲器)
中文描述： 32兆位（2Mbit的x16 /的4Mb × 8）啟動塊閃存（32兆位（200萬位x16 / 4分位× 8）啟動塊閃速存儲器）
文件頁數： 13/50頁
文件大?。?/td> 338K
代理商： LH28F320S5H-L
- 13 -
Block is Unlocked
DQ
0
= 0
Block is Locked
DQ
0
= 1
Last erase operation
DQ
1
= 0
completed successfully
Last erase operation did
DQ
1
= 1
not completed successfully
Reserved for Future Use
DQ
2
-
7
LH28F320S5-L/S5H-L
4.1
Upon initial device power-up and after exit from
deep power-down mode, the device defaults to
read array mode. This operation is also initiated by
writing the Read Array command. The device
remains enabled for reads until another command
is written. Once the internal WSM has started a
block erase, full chip erase, (multi) word/byte write
or block lock-bit configuration, the device will not
recognize the Read Array command until the WSM
completes its operation unless the WSM is
suspended via an Erase Suspend and (Multi)
Word/Byte Write Suspend command. The Read
Array command functions independently of the V
PP
voltage and RP# must be V
IH
.
Read Array Command
4.2
The identifier code operation is initiated by writing
the Read Identifier Codes command. Following the
command write, read cycles from addresses shown
in
Fig. 2
retrieve the manufacture, device, block
lock configuration and block erase status (see
Table 4
for identifier code values). To terminate the
operation, write another valid command. Like the
Read Array command, the Read Identifier Codes
command functions independently of the V
PP
voltage and RP# must be V
IH
. Following the Read
Identifier Codes command, the following information
can be read :
Read Identifier Codes Command
Table 4 Identifier Codes
CODE
NOTE :
1. X selects the specific block status code to be read. See
Fig. 2
for the device identifier code memory map.
4.3 Read Status Register Command
The status register may be read to determine when
a block erase, full chip erase, (multi) word/byte
write or block lock-bit configuration is complete and
whether the operation completed successfully (see
Table 13.1
). It may be read at any time by writing
the Read Status Register command. After writing
this command, all subsequent read operations
output data from the status register until another
valid command is written. The status register
contents are latched on the falling edge of OE# or
CE# (Either CE
0
# or CE
1
#), whichever occurs. OE#
or CE# (Either CE
0
# or CE
1
#) must toggle to V
IH
before further reads to update the status register
latch. The Read Status Register command
functions independently of the V
PP
voltage. RP#
must be V
IH
.
The extended status register may be read to
determine multi byte write availability (see
Table
13.2
). The extended status register may be read at
any time by writing the Multi Byte Write command.
After writing this command, all subsequent read
operations output data from the extended status
register, until another valid command is written. The
contents of the extended status register are latched
on the falling edge of OE# or CE# (Either CE
0
# or
CE
1
#), whichever occurs last in the read cycle.
Multi Byte Write command must be re-issued to
update the extended status register latch.
4.4 Clear Status Register Command
Status register bits SR.5, SR.4, SR.3 and SR.1 are
set to "1"s by the WSM and can only be reset by
the Clear Status Register command. These bits
indicate various failure conditions (see
Table 13.1
).
By allowing system software to reset these bits,
several operations (such as cumulatively erasing or
locking multiple blocks or writing several bytes in
ADDRESS
000000H
000001H
000002H
000003H
X0004H
(NOTE 1)
X0005H
(NOTE 1)
DATA
Manufacture Code
B0
Device Code
D4
Block Status Code
相關PDF資料
PDF描述
LH28F320SKTD-L70 32MB(2MB x8/1MB x 16 x2 Bank)Smart3/5 Dual Work Flash Memory(32M位(2M位 x8/1M位 x 16 x2 組)Smart3/5 雙工作模式閃速存儲器)
LH28F320SKTD 32M Flash Memory(32M閃速存儲器)
LH28F400BVE-TL85 4MB (512KB x 8/256KB x 16) SmartVoltage Flash Memory(4M位(512K位 x 8/256K位x 16)閃速存儲器)
LH28F400BVHE-TL85 4MB (512KB x 8/256KB x 16) SmartVoltage Flash Memory(4M位(512K位 x 8/256K位x 16)閃速存儲器)
LH28F400SUE-NC60 4M (512K 】 8, 256K 】 16) Flash Memory
相關代理商/技術參數
參數描述
LH28F320S5HNS-L90 功能描述:IC FLASH 32MBIT 90NS 56SSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤
LH28F320S5-L12 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:32-MBIT(4MBx8/2MBx16) Smart 5 Flash MEMORY
LH28F320S5-L90 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:32-MBIT(4MBx8/2MBx16) Smart 5 Flash MEMORY
LH28F320S5NS-L90 功能描述:IC FLASH 32MBIT 90NS 56SSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤
LH28F320SKTD-L70 功能描述:IC FLASH 32MBIT 70NS 56TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*