- 您現在的位置：買賣IC網 > PDF目錄370847 > M37641M8-XXXHP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37641M8-XXXHP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 40/149頁 |
| 文件大?。?/td> | 1997K |
| 代理商： | M37641M8-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁
40
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
(1) Cycle Steal Transfer Mode
When the DMAC Channel x (x = 0, 1) Transfer Mode Selection Bit
(DxTMS) is set to
“
0
”
, the respective DMAC Channel x operates in
the cycle steal transfer mode.
When a request of the specified transfer factor is generated, the
selected channel transfers one byte of data from the address indi-
cated by the Source Register into the address indicated by the
Destination Register.
There are two kinds of DMA transfer triggers supported: hardware
transfer factor and software trigger. Hardware transfer factors can
be selected by the DMACx (x = 0, 1) Hardware Transfer Request
Factor Bit (DxHR). To only use the Interrupt Request Bit, the inter-
rupt can be disabled by setting its Interrupt Enable Bit of Interrupt
Control Register to
“
0
”
.
The DMA transfer request as a software trigger can be generated
by setting the DMA Channel x (x = 0, 1) Software Transfer Trigger
Bit (DxSWT) to
“
1
”
.
The Source Registers and Transfer Destination Registers can be
either decreased or increased by 1 after transfer completion by
setting bits 0 to 3 in the DMAC Channel x (x = 0, 1) Mode Regis-
ter. When the Transfer Count Register underflows, the Source
Registers and Destination Registers are reloaded from their
latches if the DMAC Register Reload Disable Bit (DRLDD) is
“
0
”
.
The Transfer Count Register value is reloaded after an underflow
regardless of DRLDD setting. At the same time, the DMAC Inter-
rupt Request Bit and the DMA Channel x (x = 0, 1) Count Register
Underflow Flag are set to
“
1
”
.
The DMAC Channel x Disable After Count Register Underflow En-
able Bit (DxDAUE) is
“
1
”
, the DMAC Channel x Enable Bit
(DxCEN) goes to
“
0
”
at an under flows of Transfer Count Register.
By setting the DMAC Channel x (x = 0, 1) Register Reload Bit
(DxRLD) to
“
1
”
, the Source Registers, Destination Registers, and
Transfer Count Registers can be updated to the values in their re-
spective latches.
When one signal among USB endpoint signals is selected as the
hardware transfer request factor, and DMAC Channel x (x = 0, 1)
USB and Master CPU Bus Interface Enable Bit (DxUMIE) is
“
1
”
;
transfer between the USB FIFO and the master CPU bus interface
input/output buffer can be performed effectively. This transfer
function is only valid in the cycle steal mode. To validate this func-
tion, the DMAC Channel x (x = 0, 1) USB and the Master CPU Bus
Interface Enable Bit (bit 5 of DxTR) must be set to
“
1
”
. The follow-
ing shows an example of a transfer using this function.
Packet Transfer from USB FIFO to Master
CPU Bus Interface Buffer
When the USB OUT_PKT_RDY is selected as the hardware trans-
fer request factor; if the USB OUT_PKT_RDY is
“
1
”
and the
master CPU bus interface output buffer is empty, the transfer re-
quest is generated and the transfer is initiated. The
OUT_PKT_RDY retains
“
1
”
and a transfer request is generated
each time the output buffer empties until all the data in the corre-
sponding endpoint FIFO has been transferred.
The transfer ends when the last byte in the USB receive packet is
transferred and the OUT_PKT_RDY flag goes to
“
0
”
(in the case
of AUTO_CLR bit =
“
1
”
).
Byte Transfer from USB FIFO to Master CPU
Bus Interface Buffer
When the USB Endpoint 1 OUT_FIFO_NOT_EMPTY is selected
as a hardware transfer request factor, if there is data in the USB
Endpoint 1 FIFO and the master CPU bus interface output buffer
is empty; a transfer request is generated and the transfer is initi-
ated. The transfer is performed by unit of one byte.
Transfer from Master CPU Bus Interface
Buffer to USB FIFO
When the USB Endpoint X (X = 1 to 4) IN_PKT_RDY
(IN_PKT_RDY =
“
0
”
) is selected as a hardware transfer request
factor, if there is data in the master CPU bus interface output
buffer and the data in the USB FIFO is within the specified packet
size, a transfer request is generated.
The DMA transfer is terminated when a command (A0 =
“
1
”
) is in-
put to the master CPU bus interface input buffer.
The timing chart for a cycle steal transfer caused by a hardware-
related transfer request and a software trigger are shown in Figure
33 and 34, respectively.
相關PDF資料 |
PDF描述 |
|---|---|
| M37702M2-127FP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S1AFP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702S1BFP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2A | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2B | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M376420RS | 制造商:OKI 功能描述:3764-20 NOTES |
| M3764-20RS | 制造商:OKI 功能描述:3764-20 NOTES 制造商: 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP 制造商:OK International 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP |
| M3-7643A-S | 制造商:Harris Corporation 功能描述: |
| M37643F8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37643F8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。