參數資料
型號： M37920FCCHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 101/158頁
文件大?。?/td> 1261K
代理商： M37920FCCHP
47
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(2) Event counter mode [01]
Figure 32 shows the bit configuration of the timer Ai mode register
during event counter mode. In event counter mode, bit 0 of the timer
Ai mode register must be “1” and bits 1 and 5 must be “0”.
The input signal from the TAiIN pin is counted when the count start
bit shown in Figure 30 is “1” and counting is stopped when it is “0”.
Count is performed at the fall of the input signal when bit 3 is “0” and
at the rise of the signal when it is “1”.
In event counter mode, whether to increment or decrement the count
can be selected with the up-down bit or the input signal from the
TAiOUT pin.
When bit 4 of the timer Ai mode register is “0”, the up-down bit is
used to determine whether to increment or decrement the count
(decrement when the bit is “0” and increment when it is “1”). Figure
33 shows the bit configuration of the up-down register.
When bit 4 of the timer Ai mode register is “1”, the input signal from
the TAiOUT pin is used to determine whether to increment or decre-
ment the count. However, note that bit 2 must be “0” if bit 4 is “1.” It is
because if bit 2 is “1”, TAiOUT pin becomes an output pin to output
pulses.
The count is decremented when the input signal from the TAiOUT pin
is “L” and incremented when it is “H”. Determine the level of the input
signal from the TAiOUT pin before a valid edge is input to the TAiIN
pin.
An interrupt request signal is generated and the interrupt request bit
in the timer Ai interrupt control register is set when the counter
reaches 000016 (decrement count) or FFFF16 (increment count). At
the same time, the contents of the reload register is transferred to the
counter and the count is continued.
When bit 2 is “1,” each time the counter reaches 000016 (decrement
count) or FFFF16(increment count), the waveform’s polarity is re-
versed and is output from TAiOUT pin.
If bit 2 is “0”, TAiOUT pin can be used as a normal port pin.
However, if bit 4 is “1” and the TAiOUT pin is used as an output pin,
the output from the pin changes the count direction. Therefore, bit 4
must be “0” unless the output from the TAiOUT pin is to be used to se-
lect the count direction.
Fig. 32 Bit configuration of timer Ai mode register during event counter mode
Fig. 33 Bit configuration of up-down register
76543210
1
0
×
0 1 : Always “01” in event counter mode
0 : No pulse output
1 : Pulse output
0 : Count at the falling edge of input signal
1 : Count at the rising edge of input signal
0 : Increment or decrement according
to up/down bit
1 : Increment or decrement according
to TAiOUT pin input signal level
0 : Always “0” in event counter mode
× × : Not used in event counter mode
Timer A0 mode register
Timer A1 mode register
Timer A2 mode register
Timer A3 mode register
Timer A4 mode register
Addresses
5616
5716
5816
5916
5A16
Timer A0 up-down bit
Timer A1 up-down bit
Timer A2 up-down bit
Timer A3 up-down bit
Timer A4 up-down bit
Timer A2 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Timer A3 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Timer A4 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Up-down register
76543210
Address
4416
相關PDF資料
PDF描述
M37920FCCGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M38039MFL-XXXWG 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PBGA64
M38039FFLSP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64
M38039FFLKP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64
M38049FFLWG 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64
相關代理商/技術參數
參數描述
M37920FGCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4F3 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*