參數資料
型號： M37920FCCHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 109/158頁
文件大?。?/td> 1261K
代理商： M37920FCCHP
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
54
(2) Event counter mode [01]
Figure 46 shows the bit configuration of the timer Bi mode register
during event counter mode. In event counter mode, bit 0 in the timer
Bi mode register must be “1” and bit 1 must be “0”.
The input signal from the TBiIN pin is counted when the count start
bit is “1” and counting is stopped when it is “0”.
Count is performed at the fall of the input signal when bits 2, and 3
are “0” and at the rise of the input signal when bit 3 is “0” and bit 2 is
“1”.
When bit 3 is “1” and bit 2 is “0”, count is performed at the rise and
fall of the input signal.
Data write, data read and timer interrupt are performed in the same
way as for timer mode.
(3) Pulse period measurement/Pulse width
measurement mode [10]
Figure 47 shows the bit configuration of the timer Bi mode register
during pulse period measurement/pulse width measurement mode.
In pulse period measurement/pulse width measurement mode, bit 0
must be “0” and bit 1 must be “1”. Bits 6 and 7 are used to select the
clock source. The selected clock is counted when the count start bit
is “1” and counting stops when it is “0”.
The pulse period measurement mode is selected when bit 3 is “0”. In
pulse period measurement mode, the selected clock is counted dur-
ing the interval starting at the fall of the input signal from the TBiIN pin
to the next fall or at the rise of the input signal to the next rise; the
result is stored in the reload register. In this case, the reload register
acts as a buffer register.
When bit 2 is “0”, the clock is counted from the fall of the input signal
to the next fall. When bit 2 is “1“, the clock is counted from the rise of
the input signal to the next rise.
In the case of counting from the fall of the input signal to the next fall,
counting is performed as follows. As shown in Figure 48, when the
fall of the input signal from TBiIN pin is detected, the contents of the
counter is transferred to the reload register. Next, the counter is
cleared and count is started from the next clock. When the fall of the
next input signal is detected, the contents of the counter is trans-
ferred to the reload register once more, the counter is cleared, and
the count is started. The period from the fall of the input signal to the
next fall is measured in this way.
After the contents of the counter is transferred to the reload register,
an interrupt request signal is generated and the interrupt request bit
in the timer Bi interrupt control register is set. However, no interrupt
request signal is generated when the contents of the counter is trans-
ferred first to the reload register after the count start bit is set to “1”.
When bit 3 is “1”, the pulse width measurement mode is selected.
Pulse width measurement mode is the same as the pulse period
measurement mode except that the clock is counted from the fall of
the TBiIN pin input signal to the next rise or from the rise of the input
signal to the next fall as shown in Figure 49.
Fig. 45 Bit configuration of timer Bi mode register during timer mode
Fig. 46 Bit configuration of timer Bi mode register during event
counter mode
Fig. 47 Bit configuration of timer Bi mode register during pulse period
measurement/pulse width measurement mode
0 0 : Always “00” in timer mode
× × : Not used in timer mode and
may be any
Not used in timer mode
Clock source select bits
0 0 : Select f2
0 1 : Select f16
1 0 : Select f64
1 1 : Select f512
76543210
0
×
Timer B0 mode register
Timer B1 mode register
Timer B2 mode register
Addresses
5B16
5C16
5D16
0 1 : Always “01” in event counter
mode
0 0 : Count at the falling edge of
input signal
0 1 : Count at the rising edge of
input signal
1 0 : Count at the both falling edge
and rising edge of input signal
× × × : Not used in event counter mode
76543210
1
0
×
Timer B0 mode register
Timer B1 mode register
Timer B2 mode register
Addresses
5B16
5C16
5D16
1 0 : Always “10” in pulse period
measurement/pulse width
measurement mode
0 0 : Count from the falling edge of
input signal to the next falling one
0 1 : Count from the rising edge of
input signal to the next rising one
1 0 : Count from the falling edge of
input signal to the next rising one
and from the rising edge to the
next falling one
Timer Bi overflow flag
Clock source select bits
0 0 : Select f2
0 1 : Select f16
1 0 : Select f64
1 1 : Select f512
76543210
0
1
Timer B0 mode register
Timer B1 mode register
Timer B2 mode register
Addresses
5B16
5C16
5D16
相關PDF資料
PDF描述
M37920FCCGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M38039MFL-XXXWG 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PBGA64
M38039FFLSP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64
M38039FFLKP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64
M38049FFLWG 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64
相關代理商/技術參數
參數描述
M37920FGCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4F3 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*