參數資料
型號： M37920FCCHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 106/158頁
文件大?。?/td> 1261K
代理商： M37920FCCHP
51
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(4) Pulse width modulation mode [11]
Figure 41 shows the bit configuration of the timer Ai mode register
during pulse width modulation mode. In pulse width modulation
mode, bits 0, 1, and 2 must be set to “1”.
Bit 5 is used to determine whether to perform 16-bit length pulse
width modulator or 8-bit length pulse width modulator. 16-bit length
pulse width modulator is selected when bit 5 is “0” and 8-bit length
pulse width modulator is selected when it is “1”. The 16-bit length
pulse width modulator is described first.
The pulse width modulator can be started with a software trigger or
with an input signal from a TAiIN pin (external trigger).
The software trigger mode is selected when bit 4 is “0”.
Pulse width modulator is started and a pulse is output from TAiOUT
when the count start bit is set to “1”.
The external trigger mode is selected when bit 4 is “1”.
Pulse width modulation starts when a trigger signal is input from the
TAiIN pin when the count start bit is “1”. Whether to trigger at the fall
or rise of the trigger signal is determined by bit 3. The trigger is at the
fall of the trigger signal when bit 3 is “0” and at the rise when it is “1”.
When data is written to timer Ai with the pulse width modulator
halted, it is written to the reload register and the counter.
Then when the count start bit is set to “1” and a software trigger or
an external trigger is issued to start modulation, the waveform shown
in Figure 42 is output continuously.
Once modulation is started, triggers are not accepted. If the value in
the reload register is m, the duration “H” of pulse is
× m
and the output pulse period is
× (216 –1).
An interrupt request signal is generated and the interrupt request bit
in the timer Ai interrupt control register is set at each fall of the output
pulse.
The width of the output pulse is changed by updating timer data. The
update can be performed at any time. The output pulse width is
changed at the rise of the pulse after data is written to the timer.
The contents of the reload register are transferred to the counter just
before the rise of the next pulse so that the pulse width is changed
from the next output pulse.
Undefined data is read when timer Ai is read.
The 8-bit length pulse width modulator is described next.
The 8-bit length pulse width modulator is selected when the timer Ai
mode register bit 5 is “1”.
The reload register and the counter are both divided into 8-bit
halves.
1
selected clock frequency
1
selected clock frequency
The low-order 8 bits function as a prescaler and the high-order 8 bits
function as the 8-bit length pulse width modulator. The prescaler
counts the clock selected by bits 6, 7, and the contents of the timer A
clock division select register. (See Table 17.) A pulse is generated
when the counter reaches 000016 as shown in Figure 43. At the
same time, the contents of the reload register is transferred to the
counter and count is continued.
Fig. 41 Bit configuration of timer Ai mode register during pulse width
modulation mode
76543210
1
1 1 : Always “11” in pulse width modulation
mode
1 : Always “1” in pulse width modulation
mode
0
× : Software trigger
1 0 : Trigger at the falling of TAiIN input
1 1 : Trigger at the rising of TAiIN input
0 : 16-bit pulse width modulator
1 : 8-bit pulse width modulator
Clock source select bits
(See Table 17.)
Timer A0 mode register
Timer A1 mode register
Timer A2 mode register
Timer A3 mode register
Timer A4 mode register
Addresses
5616
5716
5816
5916
5A16
相關PDF資料
PDF描述
M37920FCCGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
M38039MFL-XXXWG 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PBGA64
M38039FFLSP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64
M38039FFLKP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64
M38049FFLWG 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64
相關代理商/技術參數
參數描述
M37920FGCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4F3 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*