- 您現在的位置：買賣IC網 > PDF目錄369993 > pentium II cpu (Intel Corp.) Pentium II Processor AT 450MHZ(工作頻率450兆赫茲奔II處理器) PDF資料下載
參數資料
| 型號： | pentium II cpu |
| 廠商： | Intel Corp. |
| 英文描述： | Pentium II Processor AT 450MHZ(工作頻率450兆赫茲奔II處理器) |
| 中文描述： | 奔騰II處理器在450MHz（工作頻率450兆赫茲奔二處理器） |
| 文件頁數： | 12/84頁 |
| 文件大?。?/td> | 1092K |
| 代理商： | PENTIUM II CPU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
Pentium
II Processor at 350 MHz, 400 MHz, and 450 MHz
12
Datasheet
For the processor to fully realize the low current consumption of the Stop-Grant, Sleep, and Deep
Sleep states, a Model Specific Register (MSR) bit must be set. For the MSR at 02AH (Hex), bit 26
must be set to a ‘1’ (this is the power on default setting) for the processor to stop all internal clocks
during these modes. For more information, see the
Pentium
II Processor Developer's Manual
(Order Number 243502).
Due to the inability of processors to recognize bus transactions during the Sleep and Deep Sleep
states, two-way MP systems are not allowed to have one processor in Sleep/Deep Sleep state and
the other processor in Normal or Stop-Grant state simultaneously.
2.2.1
Normal State—State 1
This is the normal operating state for the processor.
2.2.2
AutoHALT Powerdown State—State 2
AutoHALT is a low power state entered when the processor executes the HALT instruction. The
processor will transition to the Normal state upon the occurrence of SMI#, BINIT#, INIT#, or
LINT[1:0] (NMI, INTR). RESET# will cause the processor to immediately initialize itself.
The return from a System Management Interrupt (SMI) handler can be to either Normal Mode or
the AutoHALT Power Down state. See the
Intel Architecture Software Developer's Manual,
Volume III: System Programmer's Guide
(Order Number 243192) for more information.
FLUSH# will be serviced during the AutoHALT state, and the procesor will return to the
AutoHALT state.
The system can generate a STPCLK# while the processor is in the AutoHALT Power Down state.
When the system deasserts the STPCLK# interrupt, the processor will return execution to the
HALT state.
2.2.3
Stop-Grant State—State 3
The Stop-Grant state on the processor is entered when the STPCLK# signal is asserted.
Since the AGTL+ signal pins receive power from the system bus, these pins should not be driven
(allowing the level to return to V
TT
) for minimum power drawn by the termination resistors in this
state. In addition, all other input pins on the system bus should be driven to the inactive state.
BINIT# will be recognized while the processor is in Stop-Grant state. If STPCLK# is still asserted
at the completion of the BINIT# bus initialization, the processor will remain in Stop-Grant mode. If
the STPCLK# is not asserted at the completion of the BINIT# bus initialization, the processor will
return to Normal state.
FLUSH# will not be serviced during Stop-Grant state.
RESET# will cause the processor to immediately initialize itself, but the processor will stay in
Stop-Grant state. A transition back to the Normal state will occur with the deassertion of the
STPCLK# signal.
A transition to the HALT/Grant Snoop state will occur when the processor detects a snoop on the
system bus (see
Section 2.2.4
). A transition to the Sleep state (see
Section 2.2.5
) will occur with the
assertion of the SLP# signal.
相關PDF資料 |
PDF描述 |
|---|---|
| pentium II processor | 32 bit processor AT 233MHZ，266MHZ，300MHZ and 333MHZ(工作頻率233，266，300和333兆赫茲32位處理器) |
| pentium II xeon processor | pentium II xeon processor at 400 and 450 MHZ(工作頻率400和450兆赫茲奔II處理器) |
| Pentium III cpu with mobile | Pentium III processor Mobile Module Connector 2 (MMC-2)(帶移動模塊連接器2奔III處理器) |
| pentium III CPU | Pentium III Processor for the SC242 at 450MHz to 1.0GHz(SC242工作頻率450MHZ到1GHZ奔III處理器) |
| pentium III processor | 32 bit Processor Mobile Module(32 位帶移動模塊處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-ENV568K3G3 | 制造商:Panasonic Industrial Company 功能描述:TUNER |
| PEO14012 | 制造商:TE Connectivity 功能描述:RELAY SPCO 12VDC |
| PEO14024 | 制造商:TE Connectivity 功能描述:RELAY SPCO 24VDC |
| PEO96742 | 制造商:Delphi Corporation 功能描述:ASM TERM |
| PEOODO3A | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint |
發布緊急采購，3分鐘左右您將得到回復。