- 您現在的位置：買賣IC網 > PDF目錄376337 > SC1100UFH-266 (National Semiconductor Corporation) Geode⑩ Information Appliance On a Chip PDF資料下載
參數資料
| 型號： | SC1100UFH-266 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Geode⑩ Information Appliance On a Chip |
| 中文描述： | Geode⑩信息家電在一個芯片 |
| 文件頁數： | 128/348頁 |
| 文件大?。?/td> | 2063K |
| 代理商： | SC1100UFH-266 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁當前第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁第305頁第306頁第307頁第308頁第309頁第310頁第311頁第312頁第313頁第314頁第315頁第316頁第317頁第318頁第319頁第320頁第321頁第322頁第323頁第324頁第325頁第326頁第327頁第328頁第329頁第330頁第331頁第332頁第333頁第334頁第335頁第336頁第337頁第338頁第339頁第340頁第341頁第342頁第343頁第344頁第345頁第346頁第347頁第348頁
www.national.com
128
Revision 1.1
G
Core Logic Module
(Continued)
In
block
transfer mode, the DMA controller executes all of
its transfers consecutively without releasing the PCI bus.
In
demand
transfer mode, DMA transfer cycles continue to
occur as long as DRQ is high or terminal count is not
reached. In this mode, the DMA controller continues to exe-
cute transfer cycles until the I/O device drops DRQ to indi-
cate its inability to continue providing data. For this case,
the PCI bus is held by the Core Logic module until a break
in the transfers occurs.
In
cascade
mode, the channel is connected to another
DMA controller or to an ISA bus master, rather than to an
I/O device. In the Core Logic module, one of the 8237 con-
trollers is designated as the master and the other as the
slave. The HOLD output of the slave is tied to the DRQ0
input of the master (Channel 4), and the master’s DACK0#
output is tied to the slave’s HLDA input.
In each of these modes, the DMA controller can be pro-
grammed for
read
,
write,
or
verify
transfers.
Both DMA controllers are reset at power-on reset (POR) to
fixed
priority. Since master Channel 0 is actually connected
to the slave DMA controller, the slave’s four DMA channels
have the highest priority, with Channel 0 as highest and
Channel 3 as the lowest. Immediately following slave
Channel 3, master Channel 1 (Channel 5) is the next high-
est, followed by Channels 6 and 7.
DMA Controller Registers
The DMA controller can be programmed with standard I/O
cycles to the standard register space for DMA. The I/O
addresses for the DMA controller registers are listed Table
5-43 on page 265.
When writing to a channel's address or WORD Count reg-
ister, the data is written into both the base register and the
current register simultaneously. When reading a channel
address or WORD Count register, only the current address
or WORD Count can be read. The base address and base
WORD Count are not accessible for reading.
DMA Transfer Types
Each of the seven DMA channels may be programmed to
perform one of three types of transfers:
read, write, or ver-
ify
. The transfer type selected defines the method used to
transfer a byte or WORD during one DMA bus cycle.
For
read
transfer types, the Core Logic module reads data
from memory and writes it to the I/O device associated with
the DMA channel.
For
write
transfer types, the Core Logic module reads data
from the I/O device associated with the DMA channel and
writes it to the memory.
The
verify
transfer type causes the Core Logic module to
execute DMA transfer bus cycles, including generation of
memory addresses, but neither the READ nor WRITE com-
mand lines are activated. This transfer type was used by
DMA Channel 0 to implement DRAM refresh in the original
IBM PC and XT.
DMA Priority
The DMA controller may be programmed for two types of
priority schemes:
fixed
and
rotate
(I/O Ports 008h[4] and
0D0h[4] - see Table 5-43 on page 265).
In
fixed
priority, the channels are fixed in priority order
based on the descending values of their numbers. Thus,
Channel 0 has the highest priority. In
rotate
priority, the last
channel to get service becomes the lowest-priority channel
with the priority of the others rotating accordingly. This pre-
vents a channel from dominating the system.
The address and WORD Count registers for each channel
are 16-bit registers. The value on the data bus is written
into the upper byte or lower byte, depending on the state of
the internal addressing byte pointer. This pointer can be
cleared by the Clear Byte Pointer command. After this com-
mand, the first read/write to an address or WORD Count
register reads or writes to the low byte of the 16-bit register
and the byte pointer points to the high byte. The next
read/write to an address or WORD Count register reads or
writes to the high byte of the 16-bit register and the byte
pointer points back to the low byte.
When programming the 16-bit channels (Channels 5, 6,
and 7), the address which is written to the base address
register must be the real address divided by two. Also, the
base WORD Count for the 16-bit channels is the number of
16-bit WORDs to be transferred, not the number of bytes
as is the case for the 8-bit channels.
The DMA controller allows the user to program the active
level (low or high) of the DRQ and DACK# signals. Since
the two controllers are cascaded together internally on the
chip, these signals should always be programmed with the
DRQ signal active high and the DACK# signal active low.
DMA Shadow Registers
The Core Logic module contains a shadow register located
at F0 Index B8h (Table 5-29 on page 166) for reading the
configuration of the DMA controllers. This read only regis-
ter can sequence to read through all of the DMA registers.
DMA Addressing Capability
DMA transfers occur over the entire 32-bit address range of
the PCI bus. This is accomplished by using the DMA con-
troller’s 16-bit memory address registers in conjunction
with an 8-bit DMA Low Page register and an 8-bit DMA
High Page register. These registers, associated with each
channel, provide the 32-bit memory address capability. A
write to the Low Page register clears the High Page regis-
ter, for backward compatibility with the PC/AT standard.
The starting address for the DMA transfer must be pro-
grammed into the DMA controller registers and the chan-
nel’s respective Low and High Page registers prior to
beginning the DMA transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| SC1100UFH-300 | Geode⑩ Information Appliance On a Chip |
| SC11372 | MOBILE RADIO ANALOG PROCESSOR |
| SC11372CQ | MOBILE RADIO ANALOG PROCESSOR |
| SC140 | High-Performance Fix-Point DSP Core(高性能定點型數字信號處理器內核) |
| SC14402RVJG | Complete Baseband Processor for DECT Handsets |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC1100UFH-266 B1 | 制造商:Advanced Micro Devices 功能描述:I3O IC OPN |
| SC1100UFH-300 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Geode⑩ Information Appliance On a Chip |
| SC1101 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:VOLTAGE MODE PWM CONTROLLER |
| SC1101_05 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Asynchronous Voltage Mode PWM Controller |
| SC11014 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:300 / 1200 Bit Per Second Modem |
發布緊急采購，3分鐘左右您將得到回復。