- 您現在的位置：買賣IC網 > PDF目錄376337 > SC1100UFH-266 (National Semiconductor Corporation) Geode⑩ Information Appliance On a Chip PDF資料下載
參數資料
| 型號： | SC1100UFH-266 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Geode⑩ Information Appliance On a Chip |
| 中文描述： | Geode⑩信息家電在一個芯片 |
| 文件頁數： | 139/348頁 |
| 文件大?。?/td> | 2063K |
| 代理商： | SC1100UFH-266 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁當前第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁第305頁第306頁第307頁第308頁第309頁第310頁第311頁第312頁第313頁第314頁第315頁第316頁第317頁第318頁第319頁第320頁第321頁第322頁第323頁第324頁第325頁第326頁第327頁第328頁第329頁第330頁第331頁第332頁第333頁第334頁第335頁第336頁第337頁第338頁第339頁第340頁第341頁第342頁第343頁第344頁第345頁第346頁第347頁第348頁
Revision 1.1
139
www.national.com
G
Core Logic Module
(Continued)
SMI Speedup Disable:
If the Suspend Modulation feature
is being used for CPU power management, the occurrence
of an SMI disables Suspend Modulation so that the system
operates at full speed while in SMM. There are two meth-
ods used to invoke this via bit 1 of the Suspend Configura-
tion register.
1)
If F0 Index 96h[1] = 0: Use the IRQ Speedup Timer
(F0 Index 8Ch) to temporarily disable Suspend Modu-
lation when an SMI occurs.
2)
If F0 Index 96h[1] = 1: Disable Suspend Modulation
when an SMI occurs until a read to the SMI Speedup
Disable register (F1BAR0+I/O Offset 08h).
The SMI Speedup Disable register prevents VSA software
from entering Suspend Modulation while operating in
SMM. The data read from this register can be ignored. If
the Suspend Modulation feature is disabled, reading this
I/O location has no effect.
3 Volt Suspend
The Core Logic module supports the stopping of the CPU
and system clocks for a 3V Suspend state. If appropriately
configured, via the Clock Stop Control register (F0 Index
BCh), the Core Logic module asserts internal SUSP_3V
after it has gone through the SUSP#/SUSPA# handshake.
SUSP_3V is a state indicator, indicating that the system is
in a low-activity state and Suspend Modulation is active.
This indicator can be used to put the system into a low-
power state (the system clock can be turned off).
Internal SUSP_3V is connected to the enable control of the
clock generators, so that the clocks to the CPU and the
Core Logic module (and most other system devices) are
stopped. The Core Logic module continues to decrement
all of its device timers and respond to external SMI inter-
rupts after the input clock has been stopped, as long as the
32 KHz clock continues to oscillate. Any SMI event or
unmasked interrupt causes the Core Logic module to deas-
sert SUSP_3V, restarting the system clocks. As the CPU or
other device might include a PLL, the Core Logic module
holds SUSP# active for a pre-programmed period of delay
(the PLL re-sync delay) that varies from 0 to 15 ms. After
this period has expired, the Core Logic module deasserts
SUSP#, stopping Suspend. SMI# is held active for the
entire period, so that the CPU reenters SMM when the
clocks are restarted.
Save-to-Disk
Save-to-Disk is supported by the Core Logic module. In
this state, the power is typically removed from the Core
Logic module and from the entire SC1100, causing the
state of the legacy peripheral devices to be lost. Shadow
registers are provided for devices which allow their state to
be saved prior to removing power. This is necessary
because the legacy AT peripheral devices used several
write only registers. To restore the exact state of these
devices on resume, the write only register values are
“shadowed” so that the values can be saved by the power
management software.
The PC/AT compatible keyboard controller (KBC) and
floppy port (FDC) do not exist in the SC1100. However, it is
possible that one is attached on the ISA bus or the LPC
bus (e.g., in a SuperI/O device). Some FDC registers are
shadowed because they cannot be safely read. Additional
shadow registers for other functions are described in Table
5-29 "F0: PCI Header and Bridge Configuration Registers
for GPIO and LPC Support" on page 166.
5.2.10.3 Peripheral Power Management
The Core Logic module provides peripheral power man-
agement using a combination of device idle timers, address
traps, and general purpose I/O pins. Idle timers are used in
conjunction with traps to support powering down peripheral
devices.
Device Idle Timers and Traps
Idle timers are used to power manage a peripheral by
determining when the peripheral has been inactive for a
specified period of time, and removing power from the
peripheral at the end of that time period.
Idle timers are provided for the commonly-used peripherals
(FDC, IDE, Parallel/Serial Ports, and Mouse/Keyboard). In
addition, there are three user-defined timers that can be
configured for either I/O or memory ranges.
The idle timers are 16-bit countdown timers with a one sec-
ond time base, providing a timeout range of 1 to 65536
seconds (1092 minutes) (18 hours).
When the idle timer count registers are loaded with a non-
zero value and enabled, the timers decrement until one of
two possibilities happens: a bus cycle occurs at that I/O or
memory range, or the timer decrements to zero.
If a bus cycle occurs, the timer is reloaded and begins dec-
rementing again. If the timer decrements to zero, and
power management is enabled (F0 Index 80h[0] = 1), the
timer generates an SMI.
When an idle timer generates an SMI, the SMI handler
manages the peripheral power, disables the timer, and
enables the trap. The next time an event occurs, the trap
generates an SMI. This time, the SMI handler applies
power to the peripheral, resets the timer, and disables the
trap.
Relevant registers for controlling Device Idle Timers are: F0
Index 80h, 81h, 82h, 93h, 98h-9Eh, and ACh.
Relevant registers for controlling User Defined Device Idle
Timers are: F0 Index 81h, 82h, A0h, A2, A4h, C0h, C4h,
C8h, CCh, CDh, and CEh.
相關PDF資料 |
PDF描述 |
|---|---|
| SC1100UFH-300 | Geode⑩ Information Appliance On a Chip |
| SC11372 | MOBILE RADIO ANALOG PROCESSOR |
| SC11372CQ | MOBILE RADIO ANALOG PROCESSOR |
| SC140 | High-Performance Fix-Point DSP Core(高性能定點型數字信號處理器內核) |
| SC14402RVJG | Complete Baseband Processor for DECT Handsets |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC1100UFH-266 B1 | 制造商:Advanced Micro Devices 功能描述:I3O IC OPN |
| SC1100UFH-300 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Geode⑩ Information Appliance On a Chip |
| SC1101 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:VOLTAGE MODE PWM CONTROLLER |
| SC1101_05 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Asynchronous Voltage Mode PWM Controller |
| SC11014 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:300 / 1200 Bit Per Second Modem |
發(fā)布緊急采購，3分鐘左右您將得到回復。