Revision 1.1
179
www.national.com
G
Core Logic Module
(Continued)
2
Parallel/Serial Idle
Timer
Enable.
Turn on Parallel/Serial Port Idle Timer Count Register (F0 Index 9Ch) and generate an
SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges listed below, the timer is reloaded with the programmed count.
— LPT3: I/O Port 278h-27Fh.
— LPT2: I/O Port 378h-37Fh.
— COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded).
— COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded).
— COM3: I/O Port 3E8h-3EFh.
— COM4: I/O Port 2E8h-2EFh.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[2].
Floppy Disk Idle
Timer
Enable.
Turn on Floppy Disk Idle Timer Count Register (F0 Index 9Ah) and generate an SMI when
the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges listed below, the timer is reloaded with the programmed count.
— Primary floppy disk: I/O Port 3F2h-3F5h, 3F7h
— Secondary floppy disk: I/O Port 372h-375h, 377h
1
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[1].
Primary Hard Disk Idle Timer
Enable.
Turn on Primary Hard Disk Idle Timer Count Register (F0 Index 98h) and generate
an SMI when the timer expires.
0: Disable.
1: Enable.
If an access occurs in the address ranges selected in F0 Index 93h[5], the timer is reloaded with the programmed count.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[0].
Second level SMI status is reported at F0 Index 85h/F5h[0].
0
Index 82h
Power Management Enable Register 3 (R/W)
Reset Value: 00h
7
6
Reserved.
Must be set to 0.
User Defined Device 3 (UDEF3) Access Trap.
If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF3 address programming is at F0 Index C8h (Base Address register) and CEh (Control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[4].
User Defined Device 2 (UDEF2) Access Trap.
If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF2 address programming is at F0 Index C4h (Base Address register) and CDh (Control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[3].
User Defined Device 1 (UDEF1) Access Trap.
If this bit is enabled and an access occurs in the programmed address
range, an SMI is generated. UDEF1 address programming is at F0 Index C0h (base address register), and CCh (control
register).
0: Disable.
1: Enable.
Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[9].
Second level SMI status is reported at F1BAR0+I/O Offset 04h/06h[2].
5
4
Table 5-29. F0: PCI Header and Bridge Configuration Registers for GPIO and LPC Support (Continued)
Bit
Description