- 您現在的位置：買賣IC網 > PDF目錄361790 > W6692ACF ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC PDF資料下載
參數資料
| 型號： | W6692ACF |
| 英文描述： | ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| 中文描述： | 綜合業務數字網線接口|基本|的CMOS | QFP封裝| 100引腳|塑料 |
| 文件頁數： | 22/101頁 |
| 文件大?。?/td> | 851K |
| 代理商： | W6692ACF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
W6692A
- 22 -
turn off and stay at this state if INFO 0 is received on the S line. The turn off time is approximate 93
mS. The ECK command must be issued to activate the clocks.
F3 Deactivated with clock
This state is identical to "F3 Deactivated without clock" except the internal clocks are enabled. The
state is entered by the ECK command. The clocks are enabled approximately 0.5 mS to 4 mS after
the ECK command, depending on the crystal capacitances. (It is about 0.5 mS for 12pF to 33pF
capacitance).
F3 Awaiting Deactivation
The W6692A enters this state after receiving INFO 0 (in states F5 to F8) for 16 mS (64 frames). This
time constant prevents spurious effect on S interface. Any non-INFO 0 signal on the S interface
causes transition to "F5 Identifying Input" state. If this transition does not occur in a specific time (500
- 1000 mS), the microprocessor may issue DRC or ECK command to deactivate layer 1.
F4 Awaiting Signal
This state is reached when an activate request command has been received. In this state, the layer 1
transmits INFO1 and INFO 0 is received from the S interface. The software starts timer T3 of I.430
when issuing activate request command. The software deactivates layer 1 if no signal other than
INFO 0 has been received on S interface before expiration of T3.
F5 Identifying Input
After the receipt of any non-INFO 0 signal from NT, the W6692A ceases to transmit INFO 1 and
awaits identification of INFO 2 or INFO 4. This state is reached at most 50
μ
s after a signal different
from INFO 0 is present at the receiver of the S interface.
F6 Synchronized
When W6692A receives an activation signal (INFO 2), it responds with INFO 3 and waits for
normal frames (INFO 4). This state is reached at most 6 mS after an INFO 2 arrives at the S
interface (in case the clocks were disabled in "F3 Deactivated without clock").
F7 Activated
This is the normal active state with the layer 1 protocol activated in both directions. From state "F6
Synchronized" , state F7 is reached at most 0.5 mS after reception of INFO 4. From state "F3
Deactivated without clock" with the clocks disabled, state F7 is reached at most 6 mS after the
W6692A is directly activated by INFO 4.
F8 Lost Framing
This is the state where the W6692A has lost frame synchronization and is awaiting resynchronization
by INFO 2 or INFO 4 or deactivation by INFO 0.
相關PDF資料 |
PDF描述 |
|---|---|
| W6694A | TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | USB Bus ISDN S/T-Controller |
| W7020 | Telecommunication IC |
| W722 | Controller Miscellaneous - Datasheet Reference |
| W72963APOLLOELITE | BEWEGUNGSMELDER IR REICHW 12M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6694 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W6694A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W66ARX-18 | 制造商:Magnecraft 功能描述: |
| W66MAF185X | 制造商:Panasonic Industrial Company 功能描述:CRT |
發布緊急采購，3分鐘左右您將得到回復。