- 您現在的位置：買賣IC網 > PDF目錄9996 > XRT83L34IV (Exar Corporation)IC LIU T1/E1/J1 QUAD 128TQFP PDF資料下載
參數資料
| 型號： | XRT83L34IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 58/99頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-TQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
58
Asynchronous" READ Operation.
THE MOTOROLA-ASYNCHRONOUS WRITE CYCLE
If the Microprocessor Interface (of the XRT83L34 device) has been configured to operate in the Motorola-
Asynchronous Mode, then the Microprocessor should do all of the following, anytime it wishes to write a byte of
data into a register within the XRT83L34 device.
1. Place the address of the "target" register within the XRT83L34 device, on the Address Bus input pins,
A[6:0].
2. While the Microprocessor is placing the address value on the Address Bus, the Address Decoding circuitry
(within the user’s system) should assert the CS* (Chip Select) input pin of the XRT83L34 device, by tog-
gling it "LOW". This action enables further communication between the Microprocessor and the XRT83L34
Microprocessor Interface.
3. Assert the ALE/AS (Address Strobe) input pin by toggling it "LOW". This step enables the "Address Bus"
input drivers, within the Microprocessor Interface block of the XRT83L34 device.
4. Afterwards, the Microprocessor Interface should indicate that this current bus cycle is a "WRITE" operation
by toggling the WR*/R/W* (R/W*) input pin "LOW".
5. The Microprocessor should then place the byte or word that it intends to write into the "target" register, on
the bi-direction data bus, D[7:0].
6. Next, the Microprocessor should initiate the bus cycle by toggling the RD*/DS* (Data Strobe) input pin
"LOW". When the XRT83L34 device senses that the WR/R/W* (R/W*) input pin is "HIGH" and that the
RD*/DS* (Data Strobe) input pin has toggled "LOW", it will enable the "input drivers" of the bi-directional
data bus, D[7:0].
7. Immediately after the Microprocessor toggles the RD*/DS* (Data Strobe) signal "LOW", the XRT83L34
device will continue to drive the "RDY*/DTACK* output pin "HIGH". The XRT83L34 device does this in
order to inform the Microprocessor that the data (to be written into the "target" address location, within the
XRT83L34 device) is "NOT READY" to be latched into the Microprocessor Interface circuitry (within the
XRT83L34 device). In this case, the Microprocessor should continue to hold the "Data Strobe" (RD*/DS*)
input pin "LOW" until it detects the "RDY*/DTACK* output pin toggling "HIGH".
FIGURE 27. ILLLUSTRATION OF A MOTOROLA-ASYNCHRONOUS MODE READ OPERATION
ALE/AS
RD*/DS*
A[6:0]
CS*
D[7:0]
RDY/DTACK*
Not Valid
Valid Data
Address of Target Register
WR*/R/W*
Microprocessor places “target”
Address value on A[6:0]
Address Decoding
Circuitry asserts
CS*
Microprocessor keeps R/W* “high”
To denote READ Operation
Read Operation begins
Here
DTACK* toggles “l(fā)ow” to indicate
That valid data can be read from
D[7:0]
Read Operation is
Terminated Here
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E10F98SC | CONN RCPT 6POS BOX MNT W/SCKT |
| VI-21W-MX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| MS27468T15A97P | CONN RCPT 12POS JAM NUT W/PINS |
| MS27508E10B98SB | CONN RCPT 6POS BOX MNT W/SCKT |
| IDT72V243L7-5BCI | IC FIFO 2048X18 7-5NS 100BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83L34IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT83L34IVTR | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L34IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
發布緊急采購，3分鐘左右您將得到回復。