參數資料
型號: 73M1922-DB
廠商: Maxim Integrated Products
文件頁數: 71/82頁
文件大小: 0K
描述: BOARD DEMO 73M1922 20-TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
主要目的: *
嵌入式:
已用 IC / 零件: *
主要屬性: *
次要屬性: *
已供物品: 板,CD
DS_1x22_017
73M1822/73M1922 Data Sheet
Rev. 1.6
73
Auxiliary A/D Converter Status Bits
RNG
0x1A[7:0]
R
Result of Auxiliary A/D measuring the attenuated ring voltage.
Note: 1 lsb=1.31/128=~10.23 mV; 1’s compliment.
Example: 00100000
327 mV or Ring Voltage=32.7 V
LV
0x1B[7:1]
R
Line Voltage On and Off Hook
LV contains the seven most significant bits of an 8-bit A/D
representation of the voltage of the input of pin DCI. The voltage at
the DCI pin is equal to the decimal value of LV bits [7:1] x 21.87
mV. For example, if the value of 0100000 is read from LV bits
[7:1], this has a decimal value of 32, therefore DCI voltage equals
32 x 21.87 = 700 mV.
Note that the voltage at the DCI pin is the voltage divided by 5 (off
hook) or 100 (on hook). When offhook the diode bridge, switch
saturation voltage, etc. should also be added to calculate the
voltage at tip and ring.
LC
0x1C[7:1]
R
Loop Current in DC Path
Result of Auxiliary A/D measuring the Loop Current (7-bit
resolution, least significant bits only).
Note LC0=1 lsb=1.31/128=~10.23 mV=1.25 mA; magnitude only.
The value of the resistor between the rectifier bridge and the DCS
pin is assumed to be 8.2
.
Example: 0000011
30.7 mV/RE=3.74 mA; 0010000 20 mA
Note: The AC path also has ~7 mA of loop current that should be
added to get the total loop current provided by the line.
Line Sensing Control
DET
0x03[2]
R
Detection of Voltage or Current Fault
0 = None of the three conditions is detected. (Default)
1 = Indicates the detection of one of three conditions:
Under Voltage, Over Voltage and Over Current.
This status bit is reset when read. This is a maskable interrupt. It
is enabled by the ENDET bit.
ENDET
0x05[2]
W
Enables Line Sensing Interrupt on Host Side Device
This bit controls whether an interrupt is generated based upon the
detection of Under Voltage, Over Voltage and Over Current.
0 = Disable detector interrupt. (Default)
1 = Enable detector interrupt.
ENDT
0x12[1]
WO
Enable Detectors on Line Side Device
0 = UVDT, OVDT and OIDT conditions are ignored. (Default)
1 = Enables UVDT, OVDT and OIDT in the Line-Side Device and
allows them to be used in the Host-Side Device.
Under-Voltage Detection Control and Status
ENUVD
0x15[2]
WO
Enable Under Voltage Detector on Line Side Device
1 = Under Voltage Detector Enabled. When enabled, the ENNOM
bit is temporarily set to the wide bandwidth mode if an
under-voltage condition detected to allow fast reacquisition of the
line.
UVDET
0x1E[6]
R
Under-Voltage Detection on Line Side Device
0 = Under Voltage condition is not detected at VPS. (Default)
1 = Under Voltage condition is detected at VPS.
相關PDF資料
PDF描述
CM453232-R12KL INDUCTOR 120NH 770MA SMD
73S1217F-EB-LITE BOARD EVAL 73S1217F CBL/DOC/CD
UPT2D221MHD6 CAP ALUM 220UF 200V 20% RADIAL
MAX5391NEVMINIQU+ EVAL KIT MAX5391
GSC08DRTN-S93 CONN EDGECARD 16POS DIP .100 SLD
相關代理商/技術參數
參數描述
73M1966B-DB 功能描述:網絡開發工具 73M1966B Demo Brd RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
73M1966B-DB-C 功能描述:網絡開發工具 73M1966B Demo Brd w/GUI Cable RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
73M1966B-EVM 功能描述:網絡開發工具 73M1966 Demo Brd & MotherBrd RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
73M1966B-IM/F 制造商:Maxim Integrated Products 功能描述:
73M1966B-KEYCHN 功能描述:網絡開發工具 Keychain Eval Module RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V