- 您現在的位置：買賣IC網 > PDF目錄19468 > ADSP-21489KSWZ-4B (Analog Devices Inc)IC CCD SIGNAL PROCESSOR 176LQFP PDF資料下載
參數資料
| 型號： | ADSP-21489KSWZ-4B |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SIGNAL PROCESSOR 176LQFP |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | EBI/EMI，DAI，I²C，SPI，SPORT，UART/USART |
| 時鐘速率： | 400MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 5Mb |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.10V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 176-LQFP 裸露焊盤 |
| 供應商設備封裝： | 176-LQFP-EP（24x24） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Rev. B
|
Page 14 of 68
|
March 2013
PIN FUNCTION DESCRIPTIONS
Table 11. Pin Descriptions
Name
Type
State
During/
After Reset
Description
ADDR23–0
I/O/T (ipu)
High-Z/
driven low
(boot)
External Address. The processor outputs addresses for external memory and periph-
erals on these pins. The ADDR pins can be multiplexed to support the external memory
interface address, and FLAGS15–8 (I/O) and PWM (O). After reset, all ADDR pins are in
external memory interface mode and FLAG(0–3) pins are in FLAGS mode (default).
When configured in the IDP_PDAP_CTL register, IDP channel 0 scans the ADDR23–4 pins
for parallel input data.
DATA15–0
I/O/T (ipu)
High-Z
External Data. The data pins can be multiplexed to support the external memory
interface data (I/O), and FLAGS7–0 (I/O).
AMI_ACK
I (ipu)
Memory Acknowledge. External devices can deassert AMI_ACK (low) to add wait
states to an external memory access. AMI_ACK is used by I/O devices, memory
controllers, or other peripherals to hold off completion of an external memory access.
MS0–1
O/T (ipu)
High-Z
Memory Select Lines 0–1. These lines are asserted (low) as chip selects for the corre-
sponding banks of external memory. The MS1-0 lines are decoded memory address lines
that change at the same time as the other address lines. When no external memory
access is occurring the MS1-0 lines are inactive; they are active however when a condi-
tional memory access instruction is executed, when the condition evaluates as true.
The MS1 pin can be used in EPORT/FLASH boot mode. For more information, see the
ADSP-214xx SHARC Processor Hardware Reference.
AMI_RD
O/T (ipu)
High-Z
AMI Port Read Enable. AMI_RD is asserted whenever the processor reads a word from
external memory.
AMI_WR
O/T (ipu)
High-Z
AMI Port Write Enable. AMI_WR is asserted when the processor writes a word to
external memory.
FLAG0/IRQ0
I/O (ipu)
FLAG[0]
INPUT
FLAG0/Interrupt Request0.
FLAG1/IRQ1
I/O (ipu)
FLAG[1]
INPUT
FLAG1/Interrupt Request1.
FLAG2/IRQ2/MS2
I/O (ipu)
FLAG[2]
INPUT
FLAG2/Interrupt Request2/Memory Select2.
FLAG3/TMREXP/MS3
I/O (ipu)
FLAG[3]
INPUT
FLAG3/Timer Expired/Memory Select3.
The following symbols appear in the Type column of this table: A = asynchronous, I = input, O = output, S = synchronous, A/D = active drive,
O/D = open drain, and T = three-state, ipd = internal pull-down resistor, ipu = internal pull-up resistor.
The internal pull-up (ipu) and internal pull-down (ipd) resistors are designed to hold the internal path from the pins at the expected logic
levels. To pull-up or pull-down the external pads to the expected logic levels, use external resistors. Internal pull-up/pull-down resistors cannot
be enabled/disabled and the value of these resistors cannot be programmed. The range of an ipu resistor can be between 26 kΩ–63 kΩ. The
range of an ipd resistor can be between 31 kΩ–85kΩ. The three-state voltage of ipu pads will not reach to the full VDD_EXT level; at typical
conditions the voltage is in the range of 2.3 V to 2.7 V.
In this table, all pins are LVTTL compliant with the exception of the thermal diode pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MEV3S0515SC | CONV DC/DC 3W 5V IN 15V OUT SIP |
| HSM28DSAI | CONN EDGECARD 56POS R/A .156 SLD |
| MAX31855NASA+T | IC CONV THERMOCOUPLE-DGTL 8SOIC |
| ADSP-2189MKSTZ-300 | IC DSP CONTROLLER 16BIT 100-LQFP |
| VI-B1N-CX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21489KSWZ-5B | 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAG 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAGE SCALING - Trays 制造商:Analog Devices 功能描述:Digital Signal Processors & Controllers - DSP, DSC High Perf 4th Generation 制造商:Analog Devices 功能描述:450 MHz SHARC w/ Static Voltage Scaling |
| ADSP-21489KSWZENGA | 制造商:Analog Devices 功能描述:SHARC PROCESSOR - Trays |
| ADSP-21532S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-21532S: Blackfin? DSP Preliminary Data Sheet (Rev. PrD. 3/03) |
| ADSP21532SBBCENG | 制造商:Analog Devices 功能描述: |
| ADSP-21532SBCA-300 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。