- 您現在的位置：買賣IC網 > PDF目錄19468 > ADSP-21489KSWZ-4B (Analog Devices Inc)IC CCD SIGNAL PROCESSOR 176LQFP PDF資料下載
參數資料
| 型號： | ADSP-21489KSWZ-4B |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SIGNAL PROCESSOR 176LQFP |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | EBI/EMI，DAI，I²C，SPI，SPORT，UART/USART |
| 時鐘速率： | 400MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 5Mb |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.10V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 176-LQFP 裸露焊盤 |
| 供應商設備封裝： | 176-LQFP-EP（24x24） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Rev. B
|
Page 16 of 68
|
March 2013
MLBCLK1
I
Media Local Bus Clock. This clock is generated by the MLB controller that is synchro-
nized to the MOST network and provides the timing for the entire MLB interface at
49.152 MHz at FS=48 kHz. When the MLB controller is not used, this pin should be
grounded.
MLBDAT1
I/O/T in 3
pin mode. I
in 5 pin
mode.
High-Z
Media Local Bus Data. The MLBDAT line is driven by the transmitting MLB device and
is received by all other MLB devices including the MLB controller. The MLBDAT line
carries the actual data. In 5-pin MLB mode, this pin is an input only. When the MLB
controller is not used, this pin should be grounded.
MLBSIG1
I/O/T in 3
pin mode. I
in 5 pin
mode
High-Z
Media Local Bus Signal. This is a multiplexed signal which carries the Channel/Address
generated by the MLB Controller, as well as the Command and RxStatus bytes from
MLB devices. In 5-pin mode, this pin is input only. When the MLB controller is not used,
this pin should be grounded.
MLBDO1
O/T
High-Z
Media Local Bus Data Output (in 5 pin mode). This pin is used only in 5-pin MLB mode.
This serves as the output data pin in 5-pin mode. When the MLB controller is not used,
this pin should be connected to ground.
MLBSO1
O/T
High-Z
Media Local Bus Signal Output (in 5 pin mode). This pin is used only in 5-pin MLB
mode. This serves as the output signal pin in 5-pin mode. When the MLB controller is
not used, this pin should be connected to ground.
TDI
I (ipu)
Test Data Input (JTAG). Provides serial data for the boundary scan logic.
TDO
O/T
High-Z
Test Data Output (JTAG). Serial scan output of the boundary scan path.
TMS
I (ipu)
Test Mode Select (JTAG). Used to control the test state machine.
TCK
I
Test Clock (JTAG). Provides a clock for JTAG boundary scan. TCK must be asserted
(pulsed low) after power-up or held low for proper operation of the device.
TRST
I (ipu)
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low)
after power-up or held low for proper operation of the processor.
EMU
O (O/D, ipu)
High-Z
Emulation Status. Must be connected to the ADSP-2148x Analog Devices DSP Tools
product line of JTAG emulators target board connector only.
Table 11. Pin Descriptions (Continued)
Name
Type
State
During/
After Reset
Description
The following symbols appear in the Type column of this table: A = asynchronous, I = input, O = output, S = synchronous, A/D = active drive,
O/D = open drain, and T = three-state, ipd = internal pull-down resistor, ipu = internal pull-up resistor.
The internal pull-up (ipu) and internal pull-down (ipd) resistors are designed to hold the internal path from the pins at the expected logic
levels. To pull-up or pull-down the external pads to the expected logic levels, use external resistors. Internal pull-up/pull-down resistors cannot
be enabled/disabled and the value of these resistors cannot be programmed. The range of an ipu resistor can be between 26 kΩ–63 kΩ. The
range of an ipd resistor can be between 31 kΩ–85kΩ. The three-state voltage of ipu pads will not reach to the full VDD_EXT level; at typical
conditions the voltage is in the range of 2.3 V to 2.7 V.
In this table, all pins are LVTTL compliant with the exception of the thermal diode pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MEV3S0515SC | CONV DC/DC 3W 5V IN 15V OUT SIP |
| HSM28DSAI | CONN EDGECARD 56POS R/A .156 SLD |
| MAX31855NASA+T | IC CONV THERMOCOUPLE-DGTL 8SOIC |
| ADSP-2189MKSTZ-300 | IC DSP CONTROLLER 16BIT 100-LQFP |
| VI-B1N-CX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21489KSWZ-5B | 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAG 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAGE SCALING - Trays 制造商:Analog Devices 功能描述:Digital Signal Processors & Controllers - DSP, DSC High Perf 4th Generation 制造商:Analog Devices 功能描述:450 MHz SHARC w/ Static Voltage Scaling |
| ADSP-21489KSWZENGA | 制造商:Analog Devices 功能描述:SHARC PROCESSOR - Trays |
| ADSP-21532S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-21532S: Blackfin? DSP Preliminary Data Sheet (Rev. PrD. 3/03) |
| ADSP21532SBBCENG | 制造商:Analog Devices 功能描述: |
| ADSP-21532SBCA-300 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。