- 您現在的位置：買賣IC網 > PDF目錄69032 > M68HC16Y1CFC (MOTOROLA INC) 16-BIT, MROM, MICROCONTROLLER, PQFP16 PDF資料下載
參數資料
| 型號： | M68HC16Y1CFC |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, MICROCONTROLLER, PQFP16 |
| 封裝： | QFP-160 |
| 文件頁數： | 14/138頁 |
| 文件大小： | 784K |
| 代理商： | M68HC16Y1CFC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
MOTOROLA
MC68HC16Y1
110
MC68HC16Y1TS/D
RWU — Receiver Wakeup
0 = Normal receiver operation (received data recognized)
1 = Wakeup mode enabled (received data ignored until awakened)
Setting RWU enables the wakeup function, which allows the SCI to ignore received data until awakened
by either an idle line or address mark (as determined by WAKE). When in wakeup mode, the receiver
status flags are not set, and interrupts are inhibited. This bit is cleared automatically (returned to normal
mode) when the receiver is awakened.
SBK — Send Break
0 = Normal operation
1 = Break frame(s) transmitted after completion of current frame
SBK provides the ability to transmit a break code from the SCI. If the SCI is transmitting when SBK is
set, it will transmit continuous frames of zeros after it completes the current frame, until SBK is cleared.
If SBK is toggled (one to zero in less than one frame interval), the transmitter sends only one or two
break frames before reverting to idle line or commencing to send data.
Each SCSR contains flags that show SCI operational conditions. These flags can be cleared either by
hardware or by a special acknowledgment sequence. The sequence consists of SCSR read with flags
set, followed by SCDR read (write in the case of TDRE and TC). A long-word read can consecutively
access both SCSR and SCDR. This action clears receive status flag bits that were set at the time of the
read, but does not clear TDRE or TC flags.
If an internal SCI signal for setting a status bit comes after the CPU has read the asserted status bits,
but before the CPU has written or read register SCDR, the newly set status bit is not cleared — SCSR
must be read again with the bit set, and SCDR must be written or read before the status bit is cleared.
Reading either byte of SCSR causes all 16 bits to be accessed, and any status bit already set in either
byte will be cleared on a subsequent read or write of register SCDR.
TDRE — Transmit Data Register Empty Flag
0 = Register TDR still contains data to be sent to the transmit serial shifter.
1 = A new character may now be written to register TDR.
TDRE is set when the byte in register TDR is transferred to the transmit serial shifter. If TDRE is zero,
transfer has not occurred and a write to TDR will overwrite the previous value. New data is not trans-
mitted if TDR is written without first clearing TDRE.
TC — Transmit Complete Flag
0 = SCI transmitter is busy.
1 = SCI transmitter is idle.
TC is set when the transmitter finishes shifting out all data, queued preambles (mark/idle line), or
queued breaks (logic zero). The interrupt may be cleared by reading SCSR when TC is set and then by
writing the transmit data register (TDR) of SCDR.
RDRF — Receive Data Register Full Flag
0 = Register RDR is empty or contains previously read data.
1 = Register RDR contains new data.
RDRF is set when the content of the receive serial shifter is transferred to the RDR. If one or more errors
are detected in the received word, flag(s) NF, FE, and/or PF are set within the same clock cycle.
SCSRA, SCSRB — SCI Status Register
$YFFC1C, $YFFC2C
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NOT USED
TDRE
TC
RDRF
RAF
IDLE
OR
NF
FE
PF
RESET:
0
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| MCV14AI/SL | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14 |
| MCV14ATI/SL | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14 |
| MCV14AI/P | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDIP14 |
| MD8031AHB883B | 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40 |
| MD8255A | 24 I/O, PIA-GENERAL PURPOSE, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M68HC705UGANG | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| M68HC705UPGMR | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| M68HC705X16PGMR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| M68HC711CFD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68HC711CFG | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。