- 您現在的位置：買賣IC網 > PDF目錄69032 > M68HC16Y1CFC (MOTOROLA INC) 16-BIT, MROM, MICROCONTROLLER, PQFP16 PDF資料下載
參數資料
| 型號： | M68HC16Y1CFC |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, MICROCONTROLLER, PQFP16 |
| 封裝： | QFP-160 |
| 文件頁數： | 88/138頁 |
| 文件大?。?/td> | 784K |
| 代理商： | M68HC16Y1CFC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
MC68HC16Y1
MOTOROLA
MC68HC16Y1TS/D
53
erate. The following discussion assumes that VDDSYN is applied before and during reset. This minimizes
crystal start-up time. When VDDSYN is applied at power-on, start-up time is affected by specific crystal
parameters and by oscillator circuit design. VDD ramp-up time also affects pin state during reset.
During power-on reset, an internal circuit in the SCIM drives the IMB internal and external reset lines.
The circuit releases the internal reset line as VDD ramps up to the minimum specified value, and SCIM
pins are initialized. When VDD reaches the specified minimum value, the clock synthesizer VCO begins
operation. Clock frequency ramps up to the specified limp mode frequency. The external RESET line
remains asserted until the clock synthesizer PLL locks and 512 CLKOUT cycles elapse.
The SCIM clock synthesizer provides clock signals to the other MCU modules. After the clock is running
and the internal reset signal is asserted for four clock cycles, these modules reset. VDD ramp time and
VCO frequency ramp time determine how long these four cycles take. Worst case is approximately 15
milliseconds. During this period, module port pins may be in an indeterminate state. While input-only
pins can be put in a known state by means of external pull-up resistors, external logic on input/output
or output-only pins must condition the lines during this time. Active drivers require high-impedance buff-
ers or isolation resistors to prevent conflict.
3.6.4 Use of Three State Control Pin
Asserting the three-state control (TSC) input causes the MCU to put all output drivers in an inactive,
high-impedance state. The signal must remain asserted for ten clock cycles for drivers to change state.
There are certain constraints on use of TSC during power-up reset:
When the internal clock synthesizer is used (MODCLK held high during reset), synthesizer ramp-
up time affects how long the ten cycles take. Worst case is approximately 20 milliseconds from TSC
assertion.
When an external clock signal is applied (MODCLK held low during reset), pins go to high-imped-
ance state as soon after TSC assertion as ten clock pulses have been applied to the EXTAL pin.
When TSC assertion takes effect, internal signals are forced to values that can cause inadvertent
mode selection. Once the output drivers change state, the MCU must be powered down and re-
started before normal operation can resume.
3.7 Interrupts
Interrupt recognition and servicing involve complex interaction between the central processing unit, the
system integration module, and a device or module requesting interrupt service.
The CPU16 provides for eight levels of interrupt priority (0–7), seven automatic interrupt vectors, and
200 assignable interrupt vectors. All interrupts with priorities less than seven can be masked by the in-
terrupt priority (IP) field in the condition code register. The CPU16 handles interrupts as a type of asyn-
chronous exception.
Interrupt recognition is based on the states of interrupt request signals IRQ[7:1] and the IP mask value.
Each of the signals corresponds to an interrupt priority. IRQ1 has the lowest priority, and IRQ7 has the
highest priority.
The IP field consists of three bits (CCR[7:5]). Binary values %000 to %111 provide eight priority masks.
Masks prevent an interrupt request of a priority less than or equal to the mask value (except for IRQ7)
from being recognized and processed. When IP contains %000, no interrupt is masked. During excep-
tion processing, the IP field is set to the priority of the interrupt being serviced.
Interrupt request signals can be asserted by external devices or by microcontroller modules. Request
lines are connected internally by a wired NOR. Simultaneous requests with different priorities can be
made. Internal assertion of an interrupt request signal does not affect the logic state of the correspond-
ing MCU pin.
相關PDF資料 |
PDF描述 |
|---|---|
| MCV14AI/SL | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14 |
| MCV14ATI/SL | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14 |
| MCV14AI/P | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDIP14 |
| MD8031AHB883B | 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40 |
| MD8255A | 24 I/O, PIA-GENERAL PURPOSE, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M68HC705UGANG | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| M68HC705UPGMR | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| M68HC705X16PGMR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| M68HC711CFD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68HC711CFG | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。