參數資料
型號： ML60852
廠商： OKI SEMICONDUCTOR CO., LTD.
英文描述： USB Device Controller
中文描述： USB設備控制器
文件頁數： 16/81頁
文件大小： 451K
代理商： ML60852
PEDL60852-01
1
Semiconductor
ML60852
16/81
(6) Data packet transmission and reception procedure during isochronous transfer mode
Transfer of data is the major function in the isochronous transfermode. When carrying out isochronous transfer
between the ML60852 and the host, the following packet communications are carried out via the USB bus for the
data transfer of each packet.
(a) Token packet transfer (IN token or OUT token) from the host to the ML60852.
(b) Data packet transfer in the desired direction (from the host to the device or from the device to the host).
In the isochronous transfer mode, there is no handshaking that reports whether or not the packet transfer was
done normally.
The ML60852 requests the local MCU to send or receive packet data by asserting the
INTR
pin. The interrupt
cause is SOF. Upon receiving this interrupt, the local MCU writes the packet data into the transmit FIFO of the
EP set for transmission (ISO IN) in the isochronous transfer mode, or reads out data from the receive FIFO of
the EP set for reception (ISO OUT) in the isochronous transfer mode.
The above procedures of transferring one packet of data are explained below for transmission and reception
separately.
1)
During transmission
The EP for ISO IN has a two-layer FIFO configuration. One FIFO is used for storing the packet data that is
written in by the MCU via the local bus. The other FIFO is used for transmitting the stored data to the USB bus
when an IN token is received. The roles of the two FIFOs are interchanged when an SOF packet is received.
Upon receiving an SOF interrupt, the local MCU writes the data to be transmitted during the next frame into the
corresponding transmit FIFO of the EP of the ML60852. When the host transmits an IN token packet, the
ML60852 transmits to the host the packet data written in the transmit FIFO during one frame before the current
frame.
During reception
The EP for ISO OUT has a two-layer FIFO configuration. One FIFO is used for storing the packet data that is
output to the local bus when the MCU reads the received packet data. The other FIFO is used for storing the
packet data received from the USB bus. The roles of the two FIFOs are interchanged when an SOF packet is
received.
Upon receiving an SOF interrupt, the local MCU reads out the data that has been received during the previous
frame from the corresponding receive FIFO of the EP of the ML60852. When the host transmits an OUT token
and a data packet to the ML60852, the ML60852 stores that received data packet in the receive FIFO, and that
data packet is read out by the local MCU during the next frame.
2)
相關PDF資料
PDF描述
ML6190A Longwave Time Code RF Receiver LSI
ML63187 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min).
ML63189B 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min).
ML63512A 4-Bit Microcontroller with Built-in Level Detector, Melody Circuit, and Comparator,Operating at 0.9 V (Min.)
ML63514A 4-Bit Microcontroller with Built-in Level Detector, Melody Circuit, and Comparator,Operating at 0.9 V (Min.)
相關代理商/技術參數
參數描述
ML60852A 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:USB Device Controller
ML60852ATBZ010 功能描述:USB 接口集成電路 12 Mbps; USB Device Controller RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ML60852ATBZ03A 制造商:ROHM Semiconductor 功能描述:
ML-60-V2/80721 制造商:Thomas & Betts 功能描述:
ML61 制造商:MINILOGIC 制造商全稱:MINILOGIC 功能描述:Series Positive Voltage Detector
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*