- 您現在的位置：買賣IC網 > PDF目錄377971 > ML60852 (OKI SEMICONDUCTOR CO., LTD.) USB Device Controller PDF資料下載
參數資料
| 型號： | ML60852 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | USB Device Controller |
| 中文描述： | USB設備控制器 |
| 文件頁數： | 50/81頁 |
| 文件大?。?/td> | 451K |
| 代理商： | ML60852 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
PEDL60852-01
1
Semiconductor
ML60852
50/81
System Control Register (SYSCON)
Address
Type
Access type
0 x 2F
Bit map
Read/Write
D7
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
D0
0
After a hardware reset
After a bus reset
Definition
The previous value is retained
0
Software reset:
Write-only bit. Even when this bit is read out, it will be fixed at “0”. A system reset is
executed when a “1” is written in this bit. This is functionally equivalent to a hardware reset.
However, this bit itself will always remain “0”.
Power-down mode: Read/Write bit. When this bit is “0”, the oscillations will not be stopped even during the
suspend mode. When this bit is made “1”', the oscillations will be stopped in the suspend
mode and the device goes into the power save mode.
EP mode:
Read/Write bit. The 6EP mode is selected when this bit is 0 and the 5EP mode is selected
when this bit is “1”.
Pull-up control:
The content of this bit becomes valid when the ADSEL pin is “L”. When the ADSEL pin is
“L”, the internal switch becomes ON and the ALE pin is pulled up to the Vcc level if this bit is
“1”. On the other hand, if the ADSEL pin is “L” and also this bit is “0”, the internal switch is
made OFF and the ALE pin goes into the high impedance state.
Remote wakeup:
A remote wakeup is executed when a “1” is written in this bit. However, this bit itself will
always remain “0”.
PLL enable:
This bit is for enabling the internal PLL. The internal PLL cannot be used when this bit is “0”.
The signal input to the XIN pin becomes the source oscillations for the internal circuits.
The internal PLL can be used when this bit is “1”.
PLL multiplication
factor selection:
The frequency multiplication factor is 4 when this bit is “0”, and will be 8 when this bit is
“1”.
(The source oscillator frequency will be 12MHz in the 4x mode and will be 6MHz in the 8x
mode.)
Software reset
(R/W) (sereset)
Pull-up control (R/W) (plup)
Remote wakeup (R/W)
PLL Enable (pll_enable)
PLL Multiplication factor selection (fsel)
EP Mode (R/W) (ep_mod)
0 = EP0 to EP5
1 = EP0 to EP4
Power-down mode
(R/W) (power)
0 = Power saving is not
done in the suspend
mode.
1 = Power saving is done
in the suspend mode.
相關PDF資料 |
PDF描述 |
|---|---|
| ML6190A | Longwave Time Code RF Receiver LSI |
| ML63187 | 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min). |
| ML63189B | 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min). |
| ML63512A | 4-Bit Microcontroller with Built-in Level Detector, Melody Circuit, and Comparator,Operating at 0.9 V (Min.) |
| ML63514A | 4-Bit Microcontroller with Built-in Level Detector, Melody Circuit, and Comparator,Operating at 0.9 V (Min.) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML60852A | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:USB Device Controller |
| ML60852ATBZ010 | 功能描述:USB 接口集成電路 12 Mbps; USB Device Controller RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ML60852ATBZ03A | 制造商:ROHM Semiconductor 功能描述: |
| ML-60-V2/80721 | 制造商:Thomas & Betts 功能描述: |
| ML61 | 制造商:MINILOGIC 制造商全稱:MINILOGIC 功能描述:Series Positive Voltage Detector |
發布緊急采購，3分鐘左右您將得到回復。