參數資料
型號： PCI1520-EP
英文描述： Military Enhanced Plastic PC Card Controllers Data Manual
中文描述： 軍事增強塑料PC卡控制器數據手冊
文件頁數： 31/125頁
文件大?。?/td> 716K
代理商： PCI1520-EP
3
–
3
3.4.2
PCI Bus Lock (LOCK)
The bus-locking protocol defined in the
PCI Local Bus Specification
is not highly recommended, but is provided on
the PCI1520 as an additional compatibility feature. The PCI LOCK signal can be routed to the MFUNC4 terminal by
setting the appropriate values in bits 19
–
16 of the multifunction routing register. See Section 4.30,
Multifunction
Routing Register
,
for details. Note that the use of LOCK is only supported by PCI-to-CardBus bridges in the
downstream direction (away from the processor).
PCI LOCK indicates an atomic operation that may require multiple transactions to complete. When LOCK is asserted,
nonexclusive transactions can proceed to an address that is not currently locked. A grant to start a transaction on
the PCI bus does not guarantee control of LOCK; control of LOCK is obtained under its own protocol. It is possible
for different initiators to use the PCI bus while a single master retains ownership of LOCK. Note that the CardBus
signal for this protocol is CBLOCK to avoid confusion with the bus clock.
An agent may need to do an exclusive operation because a critical access to memory might be broken into several
transactions, but the master wants exclusive rights to a region of memory. The granularity of the lock is defined by
PCI to be 16 bytes, aligned. The LOCK protocol defined by the
PCI Local Bus Specification
allows a resource lock
without interfering with nonexclusive real-time data transfer, such as video.
The PCI bus arbiter may be designed to support only complete bus locks using the LOCK protocol. In this scenario,
the arbiter will not grant the bus to any other agent (other than the LOCK master) while LOCK is asserted. A complete
bus lock may have a significant impact on the performance of the video. The arbiter that supports complete bus lock
must grant the bus to the cache to perform a writeback due to a snoop to a modified line when a locked operation
is in progress.
The PCI1520 supports all LOCK protocol associated with PCI-to-PCI bridges, as also defined for PCI-to-CardBus
bridges. This includes disabling write posting while a locked operation is in progress, which can solve a potential
deadlock when using devices such as PCI-to-PCI bridges. The potential deadlock can occur if a CardBus target
supports delayed transactions and blocks access to the target until it completes a delayed read. This target
characteristic is prohibited by the
PCI Local Bus Specification
, and the issue is resolved by the PCI master using
LOCK.
3.4.3
Loading Subsystem Identification
The subsystem vendor ID register (PCI offset 40h, see Section 4.26) and subsystem ID register (PCI offset 42h, see
Section 4.27) make up a doubleword of PCI configuration space for functions 0 and 1. This doubleword register is
used for system and option card (mobile dock) identification purposes and is required by some operating systems.
Implementation of this unique identifier register is a
PC 99/PC 2001
requirement.
The PCI1520 offers two mechanisms to load a read-only value into the subsystem registers. The first mechanism
relies upon the system BIOS providing the subsystem ID value. The default access mode to the subsystem registers
is read-only, but can be made read/write by clearing bit 5 (SUBSYSRW) in the system control register (PCI offset 80h,
see Section 4.29). Once this bit is cleared, the BIOS can write a subsystem identification value into the registers at
PCI offset 40h. The BIOS must set the SUBSYSRW bit such that the subsystem vendor ID register and subsystem
ID register is limited to read-only access. This approach saves the added cost of implementing the serial electrically
erasable programmable ROM (EEPROM).
In some conditions, such as in a docking environment, the subsystem vendor ID register and subsystem ID register
must be loaded with a unique identifier via a serial EEPROM. The PCI1520 loads the data from the serial EEPROM
after a reset of the primary bus. Note that the SUSPEND input gates the PCI reset from the entire PCI1520 core,
including the serial-bus state machine (see Section 3.8.5,
Suspend Mode
, for details on using SUSPEND).
The PCI1520 provides a two-line serial-bus host controller that can interface to a serial EEPROM. See Section 3.6,
Serial-Bus Interface
,
for details on the two-wire serial-bus controller and applications.
相關PDF資料
PDF描述
PCI1620GHK Controller Miscellaneous - Datasheet Reference
PCI1620PDV Controller Miscellaneous - Datasheet Reference
PCI2050A 32-Bit. 66MHz. 9-Master PCI-to-PCI Bridge
PCI2050GHK BUS CONTROLLER
PCI2050PDV BUS CONTROLLER
相關代理商/技術參數
參數描述
PCI1520GHK 功能描述:外圍驅動器與原件 - PCI PC CARD CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PCI1520I 制造商:TI 制造商全稱:Texas Instruments 功能描述:PC CARD CONTROLLERS
PCI1520IGHK 功能描述:外圍驅動器與原件 - PCI PC CARD CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PCI1520IGHKEP 功能描述:外圍驅動器與原件 - PCI Mil Enhance PC Card Cntrlr Data Manual RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PCI1520IPDV 功能描述:外圍驅動器與原件 - PCI PC CARD CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*