- 您現在的位置：買賣IC網 > PDF目錄371179 > T7121-PL2 T7121 HDLC Interface for ISDN PDF資料下載
參數資料
| 型號： | T7121-PL2 |
| 英文描述： | T7121 HDLC Interface for ISDN |
| 中文描述： | T7121的HDLC接口用于ISDN |
| 文件頁數： | 5/68頁 |
| 文件大?。?/td> | 685K |
| 代理商： | T7121-PL2 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Lucent Technologies Inc.
5
Data Sheet
April 1997
T7121 HDLC Interface for ISDN (HIFI-64)
Pin Information
(continued)
Table 2. Pin Descriptions
Pin
1
Symbol
ALE
Type
I
Name/Function
A high-to-low transition on this pin latches the register
address on pins AD3—AD0. ALE should be held high in the demultiplexed (sep-
arate address/data) mode. ALE latches the address regardless of the state of
CS
.
Address/Data Bus.
The data bus direction is controlled by the logic states of
the
CS
,
RD
, and
WR
pins. Microprocessors using a multiplexed bus supply
address information during read or write cycles on AD6, AD3—AD0 synchro-
nized to the ALE signal. During read cycles, data is available to the micropro-
cessor on AD7—AD0. During write cycles, data is supplied by the
microprocessor on these lines. When
CS
placed in a high-impedance state (3-state). AD0 is the least significant
address/data bit.
Address Latch Enable.
2—5,
7—10
AD0—AD7
I/O
is not active, the AD7—AD0 pins are
Block move is available in MUXed address and data mode by setting the BM bit
in register 0 (R0—B3) to 1 and holding AD6 high during the address cycle of the
ALE. All writes then go directly to the transmit FIFO, and all reads address the
receive FIFO. Normal ALE mode addressing is accomplished by holding AD6
low during the ALE address cycle. Block move can be disabled by clearing the
BM bit to 0.
Ground.
Write (Active-Low).
This signal controls when data is written to the registers.
When
CS
and
WR
are low, valid data is supplied on lines AD7—AD0 by the
microprocessor. The chip latches the data on the rising edge of
Read (Active-Low).
This signal is used to read data from the registers. When
CS
and
WR
are low, the chip makes the requested data available on lines AD7—
AD0 to be read by the microprocessor.
Chip Select (Active-Low).
This signal must be low for the internal registers to
be read or written.
Interrupt.
An interrupt signal is generated when any of the interrupting condi-
tions are true. The interrupt signal remains active until the microprocessor reads
the interrupt status register (R15) if DINT (R0—B0) = 0, or until the condition
causing the interrupt is alleviated if DINT = 1. Interrupts can be masked by
appropriately setting the corresponding interrupt enable bits in the interrupt
mask register (R14). The polarity of the interrupt signal output is controlled by
the IPOL bit in register 0 (R0—B1). This pin is
Reset.
A high on this pin resets the device and forces a high-impedance
(3-state) condition on all outputs. All register bits are forced to their reset values.
(See Register section for more details.) A reset must be performed upon pow-
erup. A full chip reset occurs with or without a clock input.
Frame Synchronization.
This signal marks the beginning of a TDM highway
frame. The polarity of the input pulse can be adjusted via the FSPOL bit in regis-
ter 0 (R0—B6). Individual time slots are assigned relative to the detection of FS
by the use of registers 7—11. When HWYEN (R0—B7) is 0, the input to this pin
is ignored.
6, 22
11
V
WR
SS
—
I
WR
.
12
RD
I
13
CS
I
14
INT
O
not
an open-drain output.
15
RESET
I
16
FS
I
相關PDF資料 |
PDF描述 |
|---|---|
| T7121 | HDLC Interface for ISDN (HIFI-64)(應用于ISDN的HDLC（高階數據鏈路）接口) |
| T7502 | T7502 Dual PCM Codec with Filters |
| T7503 | T7503 Dual PCM Codec with Filters |
| T7504 | T7504 and T75504 Quad PCM Codecs with Filters |
| T7507 | T7507 Quad PCM Codec with Filters, Termination Impedance, and Hybrid Balance |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7122 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRIANGULAR TYPE |
| T7-122A1 | 功能描述:撥動開關 ON NONE OFF 1 Pole Low-Level Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-122B1 | 功能描述:撥動開關 ON NONE ON 1 Pole Low-Level Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-122D1 | 制造商:OTTO 功能描述:Toggle Switches (ON) NONE ON 1 Pole Low-Level Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle (ON) None ON SPDT Bat Toggle Screw 16A 115VAC 28VDC Panel Mount with Threads |
| T7-122E1 | 制造商:OTTO 功能描述:Toggle Switches (ON) OFF (ON) 1 Pole Low-Level Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle (ON) OFF (ON) SPDT Bat Toggle Screw 16A 115VAC 28VDC Panel Mount with Threads |
發布緊急采購，3分鐘左右您將得到回復。