參數資料
型號： XRT86VL3x
廠商： Exar Corporation
元件分類： 通信及網絡
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
文件頁數： 103/153頁
文件大?。?/td> 1316K
代理商： XRT86VL3X
XRT86VL3X
96
REV. 1.2.2
T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
When these interrupt enable bits are set and one or more Loss of Signals are present in the incoming DS1
frame, the XRT86VL3x framer will declare Receive Loss of Signal by doing the following:
Set the Receive Loss of Signal bit of the Alarm and Error Status Register to one indicating there is one or
more Loss of Signals. This status indicator is valid until the Framer Interrupt Status Register is read.
Reading this register clears the associated interrupt if Reset-Upon-Read is selected in Interrupt Control
Register (ICR). Otherwise, a write-to-clear operation by the microprocessor is required to reset these status
indicators.
The table below shows the Receive Loss of Signal status bits of the Alarm and Error Status Register.
9.5
E1 Brief discussion of alarms and error conditions
As defined in E1 specification, alarm conditions are created from defects. Defects are momentary impairments
present on the E1 trunk. If a defect is present for a sufficient amount of time (called the integration time), then
the defect becomes an alarm. Once an alarm is declared, the alarm is present until after the defect clears for a
sufficient period of time. The time it takes to clear an alarm is called the de-integration time.
Alarms are used to detect and warn maintenance personnel of problems on the E1 trunk. There are three
types of alarms:
Red alarm or Service Alarm Indication (SAI) Signal
Blue alarm or Alarm Indication Signal (AIS)
Yellow alarm or Remote Alarm Indication (RAI) Signal
To explain the error conditions and generation of different alarms, let us create a simple E1 system model. In
this model, an E1 signal is sourced from the Central Office (CO) through a Repeater to the Customer Premises
Equipment (CPE). At the same time, an E1 signal is routed from the CPE to the Repeater and back to the
Central Office.
Figure 94
below shows the simple E1 system model.
ALARM AND ERROR STATUS REGISTER (AESR) (ADDRESS = 0XNB02H)
B
IT
N
UMBER
B
IT
N
AME
B
IT
T
YPE
B
IT
D
ESCRIPTION
4
Receive Loss of
Signal State
RUR /
WC
0 - There is no change of Loss of Signal state in the incoming DS1 payload
data.
1 - There is change of Loss of Signal state in the incoming DS1 payload
data.
相關PDF資料
PDF描述
XRT86VL3X_07 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL3X Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT91L30_0611 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L306 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L30IQ STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
相關代理商/技術參數
參數描述
XRT86VL3X_07 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VL3X_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VX38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VX38_09 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VX38_0906 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*