- 您現在的位置：買賣IC網 > PDF目錄358635 > 38D5 (Renesas Technology Corp.) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | 38D5 |
| 廠商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 130/141頁 |
| 文件大?。?/td> | 2027K |
| 代理商： | 38D5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁當前第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
Rev.3.01
REJ03B0158-0301
Aug 08, 2007
Page 130 of 134
38D5 Group
3. Executing STP Instruction
Executing the STP instruction sets the LCD enable bit (bit 4 of
LCD mode register1 (address 0013
16
)) to “0” and the LCD panel
turns off. To turn the LCD panel on after returning from stop
mode, set the LCD enable bit to “1”.
4. V
L3
Pin
To use the LCD drive control circuit while V
L3
is set to the
voltage equal to V
CC
, apply the V
CC
voltage to the V
L3
pin and
write “1” to the V
L3
connection bit (bit 1 of LCD mode register 2
(address 0014
16
)).
5. LCD Drive Power Supply
Power supply capacitor may be insufficient with the division
resistance for LCD power supply, and the characteristic of the
LCD panel. In this case, there is the method of connecting the
bypass capacitor about 0.1 -0.33
μ
F to VL1 -VL3 pins. The
example of a strengthening measure of the LCD drive power
supply is shown below.
Fig. 106 Strengthening measure example of LCD drive
power supply
Notes on ROM Correction Function
1. Returning to Main Program
To return to the main program from the correction program, use
the JMP instruction (3-byte instruction).
2. Using ROM Correction Function
If the ROM correction function is used, be sure to enable the
ROM correction enable bit after setting the ROM correction
register.
3. Address
Do not set addresses other than the ROM area in the ROM
correction address registers. Also, do not set the same address in
the ROM correction address 1 register and the ROM correction
address 2 register.
4. ROM Correction Process
Include the ROM correction process in the program beforehand.
5. Using No ROM Correction Function
If the ROM correction function is not used, the ROM correction
vector can be used as normal RAM/ROM. When using as normal
RAM/ROM, be sure to set bits 1 and 0 of the ROM correction
enable register to “0” (disabled).
Notes on Clock Generating Circuit
1. Oscillation Circuit Constants
The oscillation circuit constants vary depending on the resonator.
Use values recommended by the oscillator manufacturer.
A feed-back resistor is implemented between the X
IN
and X
OUT
pins (an external feed-back resistor may be required depending
on conditions). As no feed-back resistor is implemented between
X
CIN
and X
COUT
, add a feedback resistor of about 10 M
.
2. Transition between Modes
When the MCU transits between on-chip oscillator mode, X
IN
mode, or low-speed mode, both the X
IN
and X
CIN
oscillations
must be stabilized. Be especially careful when turning the power
on and returning from stop mode. Refer to the clock state
transition diagram for a transition between each mode. Also, set
the frequency in the condition that f(X
IN
)
≥
3
×
(X
CIN
).
When X
IN
mode is not used (the X
IN
-X
OUT
oscillation or
external clock input to X
IN
is not performed), connect X
IN
to
V
CC
through a resistor.
3. Oscillation Stabilization
Before executing the STP instruction, set the values * to generate
the wait time required for oscillation stabilization to timer 1 latch
and timer 2 latch (low-order 8 bits of timer 1 and high-order 8
bits of timer 2).
*Referential values
(Set values according to your oscillator and system)
OSCSEL = “L” in the flash memory and QzROM versions:
.....................................................................0005
16
or more
OSCSEL = “H” in the QzROM version:
.....................................................................01FF
16
or more
4. Low-Speed Mode, X
IN
Mode
To use low-speed mode or X
IN
mode, wait until oscillation
stabilizes after enabling the X
IN
-X
OUT
and X
CIN
-X
COUT
oscillation, then switch to the mode.
Connect by the shortest
possible wiring.
Connect the bypass capacitor
to the V
V
L3
pins as short
as possible.
(Referential value:0.1
0.33
μ
F)
V
L3
V
L2
V
L1
相關PDF資料 |
PDF描述 |
|---|---|
| 38F1222 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| TA5M | STECKER DIN MINI 5POL |
| 70B5031 | KUPPLUNG DIN MINI 5POL |
| 39-26-3050 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 390KD05JX | 11 to 460 Volts Varistor 0.7 to 29 Joule |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 38D5_07 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics Example |
| 38D5_08 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 38D511G015FE6AD | 制造商:Sprague/Vishay 功能描述:AL015X751 |
| 38D5-FMV | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics (Flash Memory Version) |
| 38DDP11B11M1QT | 功能描述:SWITCH PUSH DPDT,O-N-O,N,SL,LF , 制造商:grayhill inc. 系列:* 零件狀態:在售 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。