參數資料
型號： 78Q8430-ARM9-EVM
廠商： Maxim Integrated Products
文件頁數： 40/88頁
文件大?。?/td> 0K
描述： EVALUATION MODULE 78Q8430 ARM9
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
系列： *
DS_8430_001
78Q8430 Data Sheet
Rev. 1.2
45
6.10.2 MAC Receive Block
The receive block receives frames from the PHY via the MII interface. It strips the preamble and SOF
and passes the remainder of the received frame data and error information to the MAC receive FIFO.
The MAC receiver passes all frames received, including error frames and collisions. Dropping of error
frames is handled by the receive producer in the QUE logic.
6.10.3 MAC Control Register
The MAC Control Register (MCR) provides controls for network operation, including:
Enable and disable transmit and receive circuit, including requests to halt at end of current packet.
Enable and disable full duplex operation and loopback modes.
Enable and disable various MAC features like excessive-deferral detection, SQE and CRC checking.
6.10.4 Transmitting a Frame
To transmit a frame, the transmit enable bit in the MCR must be set and the transmit halt request bit must
be clear. The MAC does not signal the DMA engine to transfer bytes to the MAC transmit FIFO. The
QUE transmit controller controls the transfer of bytes to the MAC transmit FIFO.
The MAC transmit block then starts transmitting the data in the FIFO, but will retain the first 64 bytes until
it has acquired the net. At that time, the MAC transmit block will request more data and transmit it until
the QUE transmit controller signals the end of the frame to be transmitted. The MAC transmit block
generates pad bytes, if needed, appends the calculated CRC to the end of the packet if requested and
transmission stops. It sets the completion bit in the Transmit Packet Status Register (TPSR), signaling
the end of a transmission, which may in turn cause an interrupt. If the QUE transmit controller indicates
an error then the MAC transmit block will transmit an MII error status and abort the frame.
The MAC transmit block does not begin transmission until the number of bytes indicated by the preload
field of the PCWR are in the MAC transmit FIFO. This is to give the IP header checksum generator a
head start in generating the checksum. This may be needed since the checksum is in the middle of the
IP header but cannot be known until the entire header is summed. The results are undefined if the
header checksum is inserted into the frame after the checksum has already been transmitted.
6.10.5 IEEE 802.3 Transmit Protocols
6.10.5.1 Interpacket Gap Timing
In half duplex mode, the gap state machine is responsible for counting the 96 bit times from the de-
assertion of the carrier sense signal, which is the inter-record gap. It breaks the 96 bit times for
inter-record gap into the first 64 bits and the last 32 bits, in order to precisely control the appropriate times
for beginning transmission. If there is any traffic within the first 64-bit times, it resets the counter and
resumes counting from zero. If there is any traffic within the last 32 bits, it continues counting and signals
the end at 96 bit times. In full duplex mode, the gap state machine starts counting at the end of
transmission and signals the end at 96 bit times (12 byte times).
6.10.5.2 Collision Processing and Back-off
If the main transmit state machine detects a collision, it starts the back-off state machine counters and
waits for the end of the back-off slot, before retransmitting the collision causing packet again. Each
back-off slot is a multiple (including zero) of 512 bit times. Each time there is a collision for the same
packet, the back-off state machine increments an internal attempt counter. A pseudo-random number
generator outputs a random number by selecting a subset of the value of the generator. The subset
grows by one bit for each subsequent attempt. This implements the equation:
0 < r < 2 k, k = min. (n, 10)
where r is the number of slot times that the MAC has to wait in case of a collision, and n is the number of
attempts. For example, after the first collision, n is 1 and r is a random number between 0 and 1. The
pseudo-random-number generator in this case is one-bit wide and gives a random number of either 0 or
相關PDF資料
PDF描述
VE-24T-EY-S CONVERTER MOD DC/DC 6.5V 50W
M1YXK-2640K IDC CABLE - MPD26K/MC26F/X
382LX392M200N082 CAP ALUM 3900UF 200V 20% SNAP
M3DEK-2606R IDC CABLE - MKR26K/MC26M/MCE26K
ECM30DCBD-S189 CONN EDGECARD 60POS R/A .156 SLD
相關代理商/技術參數
參數描述
78Q8430EBST#DB 功能描述:以太網開發工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
78Q8430STEM#DB 功能描述:以太網開發工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
78-R3 功能描述:3M SCOTCHCAST REENTERABLE SIGNAL 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
78-R4 功能描述:3M SCOTCHCAST REENTERABLE SIGNAL 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
78RB02 功能描述:SWITCH 2 POS DIP RECESSED UNSLD RoHS:否 類別:開關 >> DIP 系列:78 特色產品:RDM Series Rotary DIP Switch 標準包裝:70 系列:RDM 電路:十六進制 位置數:16 觸點額定電壓:0.1A @ 42VDC 觸動器類型:用于工具旋轉 觸動器電平:凹槽式 安裝類型:通孔 方向:頂部觸動 可清洗:是 其它名稱:EG4977-5RDMAR16PIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*