參數資料
型號： AD6636CBCZ1
廠商： Analog Devices, Inc.
元件分類： 數字上／下變頻
英文描述： 150 MSPS Wideband Digital Down-Converter (DDC)
中文描述： 150MSPS的寬帶數字下變頻器（DDC）
文件頁數： 57/72頁
文件大小： 1629K
代理商： AD6636CBCZ1
AD6636
<4>: Channel 4 Access Bit. Similar to Bit <5> for Channel 4.
Rev. 0 | Page 57 of 72
<3>: Channel 3 Access Bit. Similar to Bit <5> for Channel 3.
<2>: Channel 2 Access Bit. Similar to Bit <5> for Channel 2.
<1>: Channel 1 Access Bit. Similar to Bit <5> for Channel 1.
<0>: Channel 0 Access Bit. Similar to Bit <5> for Channel 0.
Note: If the access bits are set for more than one channel, during
write access all channels with access are written with same the
data. This is especially useful when more than one channel has
similar configurations. During a read operation, if more than
one channel has access, the read access is given to the channel
with the lowest channel number. For example, if both Channel 4
and Channel 2 have access bits set, then read access is given to
Channel 2.
Channel Enable Register <5:0>
<5>: Channel 5 Enable Bit. When this bit is set, Channel 5 logic
is enabled. When this bit is cleared, Channel 5 is disabled and
the channel’s logic does not consume any power. On power-up,
this bit comes up with Logic 0 and the channel is disabled. A
start sync does not start Channel 5 unless this bit is set before
issuing the start sync.
<4>: Channel 4 Enable Bit. Similar to Bit <5> for Channel 4.
<3>: Channel 3 Enable Bit. Similar to Bit <5> for Channel 3.
<2>: Channel 2 Enable Bit. Similar to Bit <5> for Channel 2.
<1>: Channel 1 Enable Bit. Similar to Bit <5> for Channel 1.
<0>: Channel 0 Enable Bit. Similar to Bit <5> for Channel 0.
Pin Synchronization Configuration <7:0>
<7>: Hop Synchronization Enable Bit. This bit is a global enable
for any hop synchronization involving SYNC pins. When this
bit is set, hop synchronization is enabled for all channels that
are programmed for pin synchronization. When this bit is
cleared, hop synchronization is not performed for any channel
that is programmed for pin synchronization.
<6>: Start Synchronization Enable Bit. This bit is a global enable
for any start synchronization involving SYNC pins. When this
bit is set, start synchronization is enabled for all channels that
are programmed for pin synchronization. When this bit is
cleared, start synchronization is not performed for any channel
that is programmed for pin synchronization.
<5>: First Sync Only Bit. When this bit is set, the NCO
synchronization logic recognizes only the first synchronization
event as valid. All other requests for synchronization events are
ignored as long as this bit is set. When cleared, all synchro-
nization events are acted upon.
<4>: Edge-Sensitivity Bit. When this bit is set, the rising edge on
the SYNC pin(s) is detected as a synchronization event (edge-
sensitive detection). When cleared, Logic 1 on the SYNC pin(s)
is detected as a synchronization event (level-sensitive
detection).
<3>: Enable Synchronization from SYNC3 Bit. When this bit is
set, the SYNC3 pin can be used for synchronization. When this
bit is cleared, the SYNC3 pin is ignored. This is a global enable
for all SYNC pins, and each individual channel selects which
pin it listens to.
<2>: Enable Synchronization from SYNC2 Bit. Similar to
Bit <3> for the SYNC[2] pin.
<1>: Enable Synchronization from SYNC1 Bit. Similar to
Bit <3> for the SYNC1 pin.
<0>: Enable Synchronization from SYNC0 bit. Similar to
Bit <3> for the SYNC0 pin.
Soft Synchronization Configuration <7:0>
<7>: Soft Hop Synchronization Enable Bit. When this bit is set,
hop synchronization is enabled for all channels selected using
Bits 5:0. When this bit is cleared, hop synchronization is not
performed for any channels selected using Bits 5:0.
<6>: Soft Start Synchronization Enable Bit. When this bit is set,
start synchronization is enabled for all channels selected using
Bits 5:0. When this bit is cleared, start synchronization is not
performed for any channels selected using Bits 5:0.
Bits<5:0> form the SOFT_SYNC control bits. These bits can be
written to by the controller to initiate the synchronization of a
selected channel.
<5>: Soft Sync Channel 5 Enable Bit. When this bit is set, it
enables Channel 5 to receive a hop sync or start sync, as defined
by Bits 7 and 6, respectively. When cleared, Channel 5 does not
receive any soft sync.
<4>: Soft Sync Channel 4 Enable Bit. Similar to Bit <5> for
Channel 4.
<3>: Soft Sync Channel 3 Enable Bit. Similar to Bit <5> for
Channel 3.
<2>: Soft Sync Channel 2 Enable Bit. Similar to Bit <5> for
Channel 2.
<1>: Soft Sync Channel 1 Enable Bit. Similar to Bit <5> for
Channel 1.
<0>: Soft Sync Channel 0 Enable Bit. Similar to Bit <5> for
Channel 0.
相關PDF資料
PDF描述
AD6636PCB 150 MSPS Wideband Digital Down-Converter (DDC)
AD664(中文) Monolithic 12-Bit Quad DAC(單片12位四D/A轉換器)
AD6640 12-Bit, 65 MSPS IF Sampling A/D Converter
AD6640AST 12-Bit, 65 MSPS IF Sampling A/D Converter
AD6640PCB 12-Bit, 65 MSPS IF Sampling A/D Converter
相關代理商/技術參數
參數描述
AD6636PCB 制造商:AD 制造商全稱:Analog Devices 功能描述:150 MSPS Wideband Digital Down-Converter (DDC)
AD6636XBCZ 制造商:Analog Devices 功能描述:
AD664 制造商:AD 制造商全稱:Analog Devices 功能描述:Monolithic 12-Bit Quad DAC
AD6640 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 65 MSPS IF Sampling A/D Converter
AD6640AST 制造商:Analog Devices 功能描述:ADC Single Pipelined 65Msps 12-bit Parallel 44-Pin LQFP 制造商:Analog Devices 功能描述:ADC SGL PIPELINED 65MSPS 12-BIT PARALLEL 44LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:12-BIT 65 MSPS MONOLITHIC A/D CONVERTER - Tape and Reel 制造商:Analog Devices 功能描述:Analog-Digital Converter IC Number of Bi
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*