參數資料
型號： AM188ER-25KCW
廠商： ADVANCED MICRO DEVICES INC
元件分類： 微控制器/微處理器
英文描述： CA-BAYONET
中文描述： 16-BIT, 25 MHz, MICROCONTROLLER, PQFP100
封裝： PLASTIC, QFP-100
文件頁數： 57/112頁
文件大?。?/td> 2878K
代理商： AM188ER-25KCW
Am186
TM
ER and Am188
TM
ER Microcontrollers Data Sheet
57
DRAFT
registers are used to control and monitor the interface.
Refer to Figure 14 and Figure 15 on page 58 for dia-
grams of SSI reads and writes.
Four-Pin Interface
The two enable pins SDEN1–SDEN0 can be used di-
rectly as enables for up to two peripheral devices.
Transmit and receive operations are synchronized be-
tween the master (Am186ER or Am188ER microcon-
troller) and slave (peripherals) by means of the SCLK
output. SCLK is derived from the internal processor
clock and is the processor clock divided by 2, 4, 8, or
16.
PROGRAMMABLE I/O (PIO) PINS
There are 32 pins on the Am186ER and Am188ER mi-
crocontrollers that are available as multipurpose sig-
nals. Table 3 and Table 4 on page 36 list the PIO pins.
Each of these pins can be used as a user-programma-
ble input or output signal if the normal shared function
is not needed.
If a pin is enabled to function as a PIO signal, the pre-
assigned signal function is disabled and does not affect
the level on the pin. A PIO signal can be configured to
operate as an input (with or without a weak pullup or
pulldown), as an output, or as an open-drain output.
Configuration as an open-drain output is accomplished
by keeping the appropriate PDATA bits constant in the
PIO data register and writing the data value into its as-
sociated bit position in the PIO direction register, so the
output is either driving Low or is disabled, depending
on the data.
After power-on reset, the PIO pins default to various
configurations. The column titled
Power-On Reset Sta-
tus
in Table 3 and Table 4 on page 36 lists the defaults
for the PIOs. The system initialization code must recon-
figure the PIOs as required.
Note:
WDT reset does not reset PIO registers.
The A19–A17 address pins default to normal operation
on power-on reset, allowing the processor to correctly
begin fetching instructions at the boot address
FFFF0h. The DT/R, DEN, and SRDY pins also default
to normal operation on power-on reset.
Note that emulators use A19, A18, A17, S6, and UZI.
check with their emulator vendor for limitations on em-
ulator operation.
If the AD15–AD0 bus override is enabled on power-on
reset, then S6
/
CLKSEL2
and
UZI
/
CLKSEL1 revert to
normal operation instead of PIO input with pullup. Many
emulators assert the ADEN override. If BHE/ADEN
(Am186ER microcontroller) or RFSH2/ADEN
(Am188ER microcontroller) is held Low during power-
on reset, the AD15–AD0 bus override is enabled.
相關PDF資料
PDF描述
AM20E-2402SC 20 watt dc-dc converters
AM20E-2403SC 20 watt dc-dc converters
AM20E-2405SC 20 watt dc-dc converters
AM20E-4802SC 20 watt dc-dc converters
AM20E-4803SC 20 watt dc-dc converters
相關代理商/技術參數
參數描述
AM188ER-25KI/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor
AM188ER-25KIW 制造商:Advanced Micro Devices 功能描述:MCU 16-bit E86 CISC ROMLess 3.3V 100-Pin PQFP 制造商:AMD (Advanced Micro Devices) 功能描述:MCU 16-bit E86 CISC ROMLess 3.3V 100-Pin PQFP
AM188ER-25VC/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor
AM188ER-25VCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:High-Performance, 80C186- and 80C188-Compatible, 16-Bit Embedded Microcontrollers with RAM
AM188ER-25VD\\W 制造商:Advanced Micro Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*