參數資料
型號： CP2200-GQ
廠商： Silicon Laboratories Inc
文件頁數： 19/108頁
文件大?。?/td> 0K
描述： IC ETH CTRLR SNGL-CHIP 48TQFP
標準包裝： 250
控制器類型： 以太網控制器，MAC/10Base-T
接口： 并行/串行
電源電壓： 3.1 V ~ 3.6 V
電流 - 電源： 75mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
產品目錄頁面： 627 (CN2011-ZH PDF)
配用： 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR
其它名稱： 336-1312
CP2200/1
18
Rev. 1.0
6. Functional Description
6.1. Overview
In most systems, the CP2200/1 is used for transmitting and receiving Ethernet packets, non-volatile data storage,
and controlling Link and Activity LEDs. The device is controlled using direct and indirect internal registers
accessible through the parallel host interface. All digital pins on the device are 5 V tolerant.
6.2. Reset Initialization
After every CP2200/1 reset, the following initialization procedure is recommended to ensure proper device
operation:
Step 1: Wait for the reset pin to rise. This step takes the longest during a power-on reset.
Step 2: Wait for Oscillator Initialization to complete. The host processor will receive notification through the
interrupt request signal once the oscillator has stabilized.
Step 3: Wait for Self Initialization to complete. The INT0 interrupt status register on page 31 should be
checked to determine when Self Initialization completes.
Step 4: Disable interrupts (using INT0EN and INT1EN on page 33 and page 36) for events that will not be
monitored or handled by the host processor. By default, all interrupts are enabled after every reset.
Step 5: Initialize the physical layer. See “15.7. Initializing the Physical Layer” on page 90 for a detailed
physical layer initialization procedure.
Step 6: Enable the desired Activity, Link, or Activity/Link LEDs using the IOPWR register on page 45.
Step 7: Initialize the media access controller (MAC). See “14.1. Initializing the MAC” on page 78 for a
detailed MAC initialization procedure.
page 59 for a detailed initialization procedure.
Step 9: The CP2200/1 is ready to transmit and receive packets.
6.3. Interrupt Request Signal
The CP2200/1 has an interrupt request signal (INT) that can be used to notify the host processor of pending
interrupts. The INT signal is asserted upon detection of any enabled interrupt event. Host processors that cannot
dedicate a port pin to the INT signal can periodically poll the interrupt status registers to see if any interrupt
generating events have occurred. If the /INT signal is not used, pending interrupts such a Receive FIFO Full must
still be serviced.
The 14 interrupt sources are listed below. Interrupts are enabled on reset and can be disabled by software.
Pending interrupts can be cleared (allowing the INT signal to de-assert) by reading the self-clearing interrupt
registers. See “8. Interrupt Sources” on page 30 for a complete description of the CP2200/1 interrupts.
End of Packet Reached
Packet Received
Receive FIFO Empty
“Wake-on-LAN” Wakeup Event
Receive FIFO Full
Link Status Changed
Oscillator Initialization Complete
Jabber Detected
Self Initialization Complete
Auto-Negotiation Failed
Flash Write/Erase Complete
Remote Fault Notification
Packet Transmitted
Auto-Negotiation Complete
相關PDF資料
PDF描述
CP80C86-2Z IC CPU 16BIT 5V 8MHZ 40-PDIP
CP82C50A-5Z IC ASYNC COMM ELEMENT UART 40DIP
CP82C89 IC ARBITER BUS 5V 8MHZ 20-DIP
CPC1465D IC DC TERMINATION 16-SOIC
CPC1465M IC SHDSL/ISDN DC TERM 16MLP
相關代理商/技術參數
參數描述
CP2200-GQR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201 制造商:SILABS 制造商全稱:SILABS 功能描述:SINGLE-CHIP ETHERNET CONTROLLER
CP2201EK 功能描述:以太網開發工具 ETHERNET EVAL KIT RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*