參數資料
型號： CP2200-GQ
廠商： Silicon Laboratories Inc
文件頁數： 40/108頁
文件大?。?/td> 0K
描述： IC ETH CTRLR SNGL-CHIP 48TQFP
標準包裝： 250
控制器類型： 以太網控制器，MAC/10Base-T
接口： 并行/串行
電源電壓： 3.1 V ~ 3.6 V
電流 - 電源： 75mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
產品目錄頁面： 627 (CN2011-ZH PDF)
配用： 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR
其它名稱： 336-1312
CP2200/1
Rev. 1.0
37
9. Reset Sources
Reset circuitry allows the CP2200/1 to be easily placed in a predefined default condition. Upon entry to this reset
state, the following events occur:
All direct and indirect registers are initialized to their defined reset values.
Digital pins (except /RST) are forced into a high impedance state with a weak pull-up to VDD.
Analog pins (TX+/TX–, RX+/RX–) are forced into a high impedance state without a weak pull-up.
The external oscillator is stopped and /RST driven low (except on a software reset).
All interrupts are enabled.
The contents of the transmit and receive buffers are unaffected by a reset as long as the device has maintained
sufficient supply voltage. However, since the buffer pointers are reset to their default values, the data is effectively
lost unless the host processor has kept track of the starting address and length of each packet in the buffer.
The CP2200/1 has five reset sources that place the device in the reset state. The method of entry to the reset state
determines the amount of time spent in reset and the behavior of the /RST pin. Each of the following reset sources
is described in the following sections:
Power-On
Power-Fail
Oscillator-Fail
External /RST Pin
Software Command
Upon exit from the reset state, the device automatically starts the external oscillator and waits for it to settle (this
step is skipped on software reset). Once the crystal oscillator settles, the Oscillator Initialization Complete interrupt
occurs (interrupt pin asserted), and the host processor may now access the internal registers to poll for the Self
Initialization Complete Interrupt. If the host does not have access to the interrupt signal, it should wait
approximately 1 ms after the rising edge of reset pin prior to polling the internal registers. Note that the reset pin
could remain low up to 100 ms depending on the power supply ramp time.
The device is fully functional after the Self Initialization has completed. See “6.2. Reset Initialization” on page 18 for
the recommended initialization procedure following a device reset.
相關PDF資料
PDF描述
CP80C86-2Z IC CPU 16BIT 5V 8MHZ 40-PDIP
CP82C50A-5Z IC ASYNC COMM ELEMENT UART 40DIP
CP82C89 IC ARBITER BUS 5V 8MHZ 20-DIP
CPC1465D IC DC TERMINATION 16-SOIC
CPC1465M IC SHDSL/ISDN DC TERM 16MLP
相關代理商/技術參數
參數描述
CP2200-GQR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201 制造商:SILABS 制造商全稱:SILABS 功能描述:SINGLE-CHIP ETHERNET CONTROLLER
CP2201EK 功能描述:以太網開發工具 ETHERNET EVAL KIT RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*