參數資料
型號： CP2200-GQ
廠商： Silicon Laboratories Inc
文件頁數： 72/108頁
文件大小： 0K
描述： IC ETH CTRLR SNGL-CHIP 48TQFP
標準包裝： 250
控制器類型： 以太網控制器，MAC/10Base-T
接口： 并行/串行
電源電壓： 3.1 V ~ 3.6 V
電流 - 電源： 75mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
產品目錄頁面： 627 (CN2011-ZH PDF)
配用： 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR
其它名稱： 336-1312
CP2200/1
66
Rev. 1.0
12.6. Advanced Receive Buffer Operation
Receive buffer operation is automatically handled by hardware and does not require any assistance from the host
processor. Note: The information in this section is provided for reference purposes only and will typically
not be used except when debugging a problem and additional control over the receive buffer is required.
Figure 18 shows a detailed block diagram of the receive buffer. As packets arrive and pass through the receive
filter, they are added to the circular receive buffer at the address pointed to by the tail pointer. The FIFO tail pointer
is incremented after each byte is received. As soon as a new packet arrives, the receive buffer controller searches
for an unused TLB slot to store data about the received packet. If an unused TLB slot is found, it is claimed and
assigned to the packet currently being received by setting the slot’s valid bit to ‘1’. A Packet Received interrupt will
be generated after the entire packet is copied to the buffer. If all 8 slots are full (valid bits for all slots are set to ‘1’),
then the packet will be dropped and a Receive FIFO Full interrupt will be generated.
Each TLB slot holds information about its assigned packet such as starting address in the buffer, length, and
information about the packet such as the type (broadcast, multicast, unicast) and any errors that occurred during
reception (CRC error, incomplete packet, etc.). The receive buffer controller rotates through the TLB slots in a
circular fashion. For debugging purposes, the host processor may access any TLB slot using the TLB registers
listed in Table 17.
Figure 18. Receive Buffer Block Diagram
The oldest packet received starts at the address pointed to by the FIFO head pointer. This packet (packet #1 in
Figure 18) will be referred to as the current packet. The FIFO head pointer is used by the AutoRead interface to
read data from the current packet. As data is read using the AutoRead interface, the FIFO head pointer is
incremented until the entire packet is read out. Once the packet is read out, the host processor must clear the valid
bit of the packet by writing a ‘1’ to RXCLRV (RXCN.2). If the host processor chooses not to read the entire packet,
the valid bit should be cleared (and unread data skipped) by writing a ‘1’ to RXSKIP (RXCN.1).
A copy of the TLB slot associated with the current packet is always available by reading the CTLB registers listed in
Table 16. The same information can be obtained by reading CPTLB to determine the current TLB slot, then directly
accessing the slot using the registers in Table 17.
0
1
0
FIFO Head Pointer
FIFO Tail Pointer
Packet #1
Packet #2
Packet #3
4 KB
Receive
Buffer
TLB0
TLB1
TLB2
TLB3
TLB4
TLB5
TLB6
TLB7
Translation Look-aside Buffer
(8-entry circular or random access)
Current packet address,
length, and information.
Valid Bit
CPINFO/
CPLEN/
CPADDR
Copy of
Current TLB
CPTLB
Current TLB
Entry Number
(e.g. 0 for TLB0)
RXAUTORD
Autoread interface automatically manages read pointers. TLB Entries are typically not
accessed by the host.
相關PDF資料
PDF描述
CP80C86-2Z IC CPU 16BIT 5V 8MHZ 40-PDIP
CP82C50A-5Z IC ASYNC COMM ELEMENT UART 40DIP
CP82C89 IC ARBITER BUS 5V 8MHZ 20-DIP
CPC1465D IC DC TERMINATION 16-SOIC
CPC1465M IC SHDSL/ISDN DC TERM 16MLP
相關代理商/技術參數
參數描述
CP2200-GQR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201 制造商:SILABS 制造商全稱:SILABS 功能描述:SINGLE-CHIP ETHERNET CONTROLLER
CP2201EK 功能描述:以太網開發工具 ETHERNET EVAL KIT RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*