- 您現在的位置：買賣IC網 > PDF目錄16530 > EVAL-ADV7173EBZ (Analog Devices Inc)BOARD EVALUATION FOR ADV7173 PDF資料下載
參數資料
| 型號： | EVAL-ADV7173EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/60頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADV7173 |
| 標準包裝： | 1 |
| 系列： | Advantiv® |
| 主要目的： | 視頻，視頻處理 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADV7173 |
| 主要屬性： | NTSC/PAL 數字視頻編碼器 |
| 次要屬性： | I²C 接口 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
REV. B
ADV7172/ADV7173
–23–
POWER-ON RESET
After power-up, it is necessary to execute a reset operation. A
reset occurs on the falling edge of a high-to-low transition on
the
RESET pin. This initializes the pixel port such that the pixel
inputs P7–P0 are not selected. After reset, the ADV7172/
ADV7173 is automatically set up to operate in NTSC/PAL mode,
depending on the PAL_NTSC pin. The subcarrier frequency
registers are automatically loaded with the correct values for
PAL or NTSC. All other registers, with the exception of Mode
Registers 1 and 2, are set to 00H. Mode Register 1 is set to 07H.
This is to ensure DACs D, E, and F are ON after power-up.
All bits of Mode Register 2 are set to “0,” with the exception of
Bit 3 (i.e., Mode Register 2 reads 08H). Bit MR23 of Mode
Register 2 is set to Logic “1.” This enables the 7.5 IRE pedestal.
RESET SEQUENCE
When
RESET becomes active, the ADV7172/ADV7173 reverts
to the default output configuration. DACs A, B, C are off and
DACs D, E, F are powered on and output composite, luma and
chroma signals respectively. Mode Register 2, Bit 6 (MR26),
resets to “0.” The ADV7172/ADV7173 internal timing is under
the control of the logic level on the NTSC_PAL pin.
When
RESET is released Y, Cr, Cb values corresponding to a
black screen are input to the ADV7172/ADV7173. Output
timing signals are still suppressed at this stage.
When the user requires valid data, MR26 is set to “1” to allow
the valid pixel data to pass through the encoder. Digital output
timing signals become active and the encoder timing is now
under the control of the timing registers. If, at this stage, the
user wishes to select a video standard different from that on the
NTSC_PAL pin, Mode Register 2, Bit 5 (MR25) is set (“1”)
and the video standard required is selected by programming
Mode Register 0. Figure 36 illustrates the reset sequence timing.
SLEEP MODE
If after reset the SCRESET/RTC and NTSC_PAL pins are
both set to high, the part ADV7172/ADV7173 will power-up
in sleep mode to facilitate low power consumption before all
registers have been initialized. If Mode Register 6, Bit 0 (MR60) is
then set to (“1”) sleep mode control passes to Mode Register 2,
Bit 7 (i.e., control via I
2C).
SCH PHASE MODE
The SCH phase is configured in default mode to reset every
four (NTSC) or eight (PAL) fields to avoid an accumulation of
SCH phase error over time. In an ideal system, zero SCH phase
error would be maintained forever, but in reality, this is impos-
sible to achieve due to clock frequency variations. This effect is
reduced by the use of a 32-bit DDS, which generates this SCH.
Resetting the SCH phase every four or eight fields avoids the
accumulation of SCH phase error, and results in very minor
SCH phase jumps at the start of the four or eight field sequence.
Resetting the SCH phase should not be done if the video source
does not have stable timing or the ADV7172/ADV7173 is con-
figured in RTC mode (MR41 = “1” and MR42 = “1”). Under
these conditions (unstable video) the subcarrier phase reset should
be enabled (MR42 = “0” and MR41 = “1”) but no reset applied.
In this configuration the SCH phase will never be reset, which
that the output video will now track the unstable input video.
The subcarrier phase reset when applied will reset the SCH
phase to Field 0 at the start of the next field (e.g., subcarrier
phase reset applied in Field 5 (PAL) on the start of the next
field SCH phase will be reset to Field 0).
XXXXXXX
DIGITAL TIMING SIGNALS SUPPRESSED
BLACK VALUE
BLACK VALUE WITH SYNC
VALID VIDEO
0
1
TIMING ACTIVE
RESET
COMPOSITE/Y
CHROMA
MR26
PIXEL DATA VALID
DIGITAL TIMING
0
512
Figure 36.
RESET Sequence Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MCP121T-450E/TT | IC SUPERVISOR 4.38V LOW S0T-23B |
| VE-J0H-EZ-S | CONVERTER MOD DC/DC 52V 25W |
| M3TTK-1036R | IDC CABLE - MSD10K/MC10M/MSD10K |
| UVR1V331MPD1TD | CAP ALUM 330UF 35V 20% RADIAL |
| ECC13DRXS-S734 | CONN EDGECARD 26POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADV7174EBM | 制造商:AD 制造商全稱:Analog Devices 功能描述:Chip Scale PAL/NTSC Video Encoder with Advanced Power Management |
| EVAL-ADV7179EBM | 制造商:Analog Devices 功能描述:EVALUATION BOARD IC - Bulk |
| EVAL-ADV7179EBZ | 功能描述:BOARD EVALUATION FOR ADV7179 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-ADV7180-32EBZ | 功能描述:BOARD EVAL FOR ADV7180 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-ADV7180-48EBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder |
發布緊急采購，3分鐘左右您將得到回復。