參數資料
型號： MCIMX31_07
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Multimedia Applications Processors
中文描述： 多媒體應用處理器
文件頁數： 9/108頁
文件大?。?/td> 1235K
代理商： MCIMX31_07
Signal Descriptions
i.MX31/i.MX31L Advance Information, Rev. 2.3
Freescale Semiconductor
9
3
Signal Descriptions
Signal descriptions are in the reference manual. Special signal considerations are listed following this
paragraph. The BGA ball assignment is in
Section 5, “Package Information and Pinout
”
on page 98
.
Special Signal Considerations:
Tamper detect (GPIO1_6)
Tamper detect logic is used to issue a security violation. This logic is activated if the tamper detect
input is asserted.
The tamper detect logic is disabled after reset. After enabling the logic, it is impossible to disable
it until the next reset. The GPR[16] bit functions as the tamper detect enable bit.
GPIO1_6 functions similarly to other I/O with GPIO capabilities regardless of the status of the
tamper detect enable bit. (For example, the GPIO1_6 can function as an input with GPIO
capabilities, such as sampling through PSR or generating interrupts.)
Power ready (GPIO1_5)
The power ready input, GPIO1_5, should be connected to an external power management IC power
ready output signal. If not used, GPIO1_5 must either be (a) externally pulled-up to NVCC1 or (b)
a no connect, internally pulled-up by enabling the on-chip pull-up resistor. GPIO1_5 is a dedicated
input and cannot be used as a general-purpose input/output.
SJC_MOD
SJC_MOD must be externally connected to GND for normal operation. Termination to GND
through an external pull-down resistor (such as 1 k
Ω
) is allowed, but the value should be much
smaller than the on-chip 100 k
Ω
pull-up.
CE_CONTROL
CE_CONTROL is a reserved input and must be externally tied to GND through a 1 k
Ω
resistor.
TTM_PAD
TTM_PAD is for Freescale factory use only. Control bits indicate pull-up/down disabled. However,
TTM_PAD is actually connected to an on-chip pull-down device. Users must either float this signal
or tie it to GND.
M_REQUEST and M_GRANT
These two signals are not utilized internally. The user should make no connection to these signals.
Clock Source Select (CLKSS)
The CLKSS is the input that selects the default reference clock source providing input to the DPLL.
To select CKIH, tie CLKSS to NVCC1. To select CKIL, tie CLKSS to ground. After initialization,
the reference clock source can be changed (initial setting is overwritten) by programming the
PRCS bits in the CCMR.
相關PDF資料
PDF描述
MCIMX31 Multimedia Applications Processors
MCL245 SILICON EPITAXIAL PLANAR DIODE
MCL908QT1 M68HC08 Microcontrollers
MCM63R836 MCM63R836
MCN51-30S3-PFA 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
相關代理商/技術參數
參數描述
MCIMX31ADSE 功能描述:KIT DEV ADS I.MX31 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
MCIMX31ADSE/C 功能描述:開發板和工具包 - ARM I.MX31 APP DEV SYS RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
MCIMX31ADSE/C 制造商:Freescale Semiconductor 功能描述:Development Kit
MCIMX31C 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors
MCIMX31C_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors for Industrial and Automotive Products
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*