參數資料
型號： MFRC53101T
廠商： NXP Semiconductors N.V.
元件分類： 通信及網絡
英文描述： ISO-IEC 14443 reader IC
封裝： MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html<1<week 51, 2004,;MFRC53101T/0FE<SOT287-1 (SO32)|<<http://www.nxp.com/packages/SOT287-1.html<
文件頁數： 34/116頁
文件大?。?/td> 862K
代理商： MFRC53101T
MFRC531_34
NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.4 — 26 January 2010
056634
34 of 116
NXP Semiconductors
MFRC531
ISO/IEC 14443 reader IC
Automatic calibration can be set-up to execute at the end of each Transceive command if
bit ClkQCalib = logic 0. Setting bit ClkQCalib = logic 1 disables all automatic calibrations
except after the reset sequence. Automatic calibration can also be triggered by the
software when bit ClkQCalib has a logic 0 to logic 1 transition.
Remark:
The duration of the automatic Q-clock calibration is 65 oscillator periods or
approximately 4.8
μ
s.
The ClockQControl register’s ClkQDelay[4:0] value is proportional to the phase-shift
between the Q-clock and the I-clock. The ClkQ180Deg status flag bit is set when the
phase-shift between the Q-clock and the I-clock is greater than 180
°
.
Remark:
The StartUp configuration file enables automatic Q-clock calibration after a reset
If bit ClkQCalib = logic 1, automatic calibration is not performed. Leaving this bit set to
logic 1 can be used to permanently disable automatic calibration.
It is possible to write data to the ClkQDelay[4:0] bits using the microprocessor. The
aim could be to disable automatic calibration and set the delay using the software.
Configuring the delay value using the software requires bit ClkQCalib to have been
previously set to logic 1 and a time interval of at least 4.8
μ
s has elapsed. Each delay
value must be written with bit ClkQCalib set to logic 1. If bit ClkQCalib is logic 0, the
configured delay value is overwritten by the next automatic calibration interval.
9.10.2.2
Amplifier
The demodulated signal must be amplified by the variable amplifier to achieve the best
performance. The gain of the amplifiers can be adjusted using the RxControl1 register
Gain[1:0] bits; see
Table 27
.
Table 27.
See
Table 83 “RxControl1 register bit descriptions” on page 61
for additional information.
Register setting
Fig 12. Automatic Q-clock calibration
001aak616
calibration impulse
from reset sequence
a rising edge initiates
Q-clock calibration
ClkQCalib bit
calibration impulse
from end of
Transceive command
Gain factors for the internal amplifier
Gain factor [dB]
(simulation results)
20
24
31
35
00
01
10
11
相關PDF資料
PDF描述
MFRX85201HD Secure contactless reader solution
MMBD4148 High-speed switching diode
MMBD6050-V-GS08 SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel
MMBD6050-V-GS18 SWITING 70V 0.2A 3PIN SOT-23 - Tape and Reel
MMBD7000-V-GS08 Diode Small Signal Switching 100V 0.2A 3-Pin SOT-23 T/R
相關代理商/技術參數
參數描述
MFRC53101T/0FE,112 功能描述:RFID應答器 MIFARE HS READER RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
MFRC53101T/0FE112 制造商:NXP Semiconductors 功能描述:CNTCLESS RC 5V ISO14443-A
MFRC53101T/0FE112 制造商:NXP Semiconductors 功能描述:IC RFID READER 13.56MHZ SOIC-32
MFRC630 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Contactless reader IC
MFRC63001HN,518 制造商:NXP Semiconductors 功能描述:MFRC63001HN/HVQFN32/REEL13DP// - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*