參數資料
型號： S71PL191HB0BFI100
廠商： SPANSION LLC
元件分類： 存儲器
英文描述： SPECIALTY MEMORY CIRCUIT, PBGA73
封裝： 9 X 13 MM, LEAD FREE, FBGA-73
文件頁數： 146/172頁
文件大?。?/td> 4662K
代理商： S71PL191HB0BFI100
May 7, 2004 S29PL127H_129H_00A1
S29PL127H/S29PL129H
59
Pre l i m i n a r y
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin which indicates whether an
Embedded Algorithm is in progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command sequence. Since RY/BY#
is an open-drain output, several RY/BY# pins can be tied together in parallel with
a pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or programming. (This
includes programming in the Erase Suspend mode.) If the output is high (Ready),
the device is in the read mode, the standby mode, or one of the banks is in the
erase-suspend-read mode.
Table 18 shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm
is in progress or complete, or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is valid after the rising edge
of the final WE# pulse in the command sequence (prior to the program or erase
operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cy-
cles to any address cause DQ6 to toggle. The system may use either OE# or CE#
to control the read cycles. When the operation is complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing
are protected, DQ6 toggles for approximately 400 s, then returns to reading
array data. If not all selected sectors are protected, the Embedded Erase algo-
rithm erases the unprotected sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine whether a sector is ac-
tively erasing or is erase-suspended. When the device is actively erasing (that is,
the Embedded Erase algorithm is in progress), DQ6 toggles. When the device en-
ters the Erase Suspend mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or erase-suspended. Alter-
natively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector, DQ6 toggles for approxi-
mately 1 s after the program command sequence is written, then returns to
reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling
once the Embedded Program algorithm is complete.
Table 18 shows the outputs for Toggle Bit I on DQ6. Figure 8 shows the toggle bit
algorithm. Figure 21 in the “AC Characteristics” section shows the toggle bit tim-
ing diagrams. Figure 22 shows the differences between DQ2 and DQ6 in graphical
form. See also the subsection on DQ2: Toggle Bit II.
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular
sector is actively erasing (that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit II is valid after the rising
edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have
been selected for erasure. (The system may use either OE# or CE# to control the
read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or
is erase-suspended. DQ6, by comparison, indicates whether the device is actively
相關PDF資料
PDF描述
S71VS128RC0ZHK203 SPECIALTY MEMORY CIRCUIT, PBGA56
S71VS128RC0ZHK2L2 SPECIALTY MEMORY CIRCUIT, PBGA56
S71WS512ND0BAWEH SPECIALTY MEMORY CIRCUIT, PBGA84
S72NS512PE0AHGL02 SPECIALTY MEMORY CIRCUIT, PBGA133
S7911 PIN PHOTO DIODE
相關代理商/技術參數
參數描述
S71PL254 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
S71PL254J 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
S71PL254J04BAW0Z0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
S71PL254J04BAW0Z2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
S71PL254J04BAW0Z3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*