- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C970 (Advanced Micro Devices, Inc.) PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus PDF資料下載
參數資料
| 型號： | AM79C970 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus |
| 中文描述： | PCnetTM - PCI單芯片以太網控制器的PCI總線 |
| 文件頁數： | 71/168頁 |
| 文件大?。?/td> | 943K |
| 代理商： | AM79C970 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁
AMD
P R E L I M I N A R Y
1-938
Am79C970
Transmit Operation
The transmit operation and features of the PCnet-PCI
controller are controlled by programmable options. The
PCnet-PCI controller offers a136-byte Transmit FIFO to
provide frame buffering for increased system latency,
automatic retransmission with no FIFO reload, and
automatic transmit padding.
Transmit Function Programming
Automatic transmit features such as retry on collision,
FCS generation/transmission, and pad field insertion
can all be programmed to provide flexibility in the
(re-)transmission of messages.
Disable retry on collision (DRTY) is controlled by the
DRTY bit of the Mode register (CSR15) in the initiali-
zation block.
Automatic pad field insertion is controlled by the
APAD_XMT bit in CSR4. If APAD_XMT is set, auto-
matic pad field insertion is enabled, the DXMTFCS fea-
ture is over-ridden, and the 4-byte FCS will be added to
the transmitted frame unconditionally. If APAD_XMT is
clear, no pad field insertion will take place and runt
packet transmission is possible.
The disable FCS generation/transmission feature can
be programmed dynamically on a frame by frame basis.
See the ADD_FCS description of TMD1.
Transmit FIFO Watermark (XMTFW) in CSR80 sets the
point at which the BMU requests more data from the
transmit buffers for the FIFO. A minimum of XMTFW
empty spaces must be available in the transmit FIFO be-
fore the BMU will request the system bus in order to
transfer transmit packet data into the transmit FIFO.
Transmit Start Point (XMTSP) in CSR80 sets the point
when the transmitter actually attempts to transmit a
frame onto the media. A minimum of XMTSP bytes must
be written to the transmit FIFO for the current frame be-
fore transmission of the current frame will begin. (When
automatically padded packets are being sent, it is con-
ceivable that the XMTSP is not reached when all of the
data has been transferred to the FIFO. In this case, the
transmission will begin when all of the packet data has
been placed into the transmit FIFO.)
When the entire frame is in the FIFO, attempts at trans-
mission of preamble will commence regardless of the
value in XMTSP. The default value of XMTSP is 10b,
meaning there has to be 64 bytes in the Transmit FIFO
to start a transmission.
Automatic Pad Generation
Transmit frames can be automatically padded to extend
them to 64 data bytes (excluding preamble). This allows
the minimum frame size of 64 bytes (512 bits) for
802.3/Ethernet to be guaranteed with no software inter-
vention from the host/controlling process.
Setting the APAD_XMT bit in CSR4 enables the auto-
matic padding feature. The pad is placed between the
LLC data field and FCS field in the 802.3 frame.FCS is
always added if the frame is padded, regardless of the
state of DXMTFCS. The transmit frame will be padded
by bytes with the value of 00h. The default value of
APAD_XMT is 0; this will disable auto pad generation af-
ter H_RESET.
Preamble
1010....1010
Sync
10101011
Destination
Address
Source
Address
Length
LLC
Data
Pad
FCS
4
Bytes
46 — 1500
Bytes
2
Bytes
6
Bytes
6
Bytes
8
Bits
56
Bits
18220C-29
Figure 27
.
ISO 8802-3(IEEE/ANSI 802.3) Data Frame
It is the responsibility of upper layer software to correctly
define the actual length field contained in the message
to correspond to the total number of LLC Data bytes en-
capsulated in the packet (length field as defined in the
ISO 8802-3 (IEEE/ANSI 802.3) standard). The length
value contained in the message is not used by the
PCnet-PCI controller to compute the actual number of
pad bytes to be inserted. The PCnet-PCI controller will
append pad bytes dependent on the actual number of
bits transmitted onto the network. Once the last data
byte of the frame has completed, prior to appending the
FCS, the PCnet-PCI controller will check to ensure that
544 bits have been transmitted. If not, pad bytes are
added to extend the frame size to this value, and the
FCS is then added.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C971VCW | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971 | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971KCW | IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE |
| AM79C972BKCW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BKIW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C970A | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AKC | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AKC\\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AKC\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。