參數資料
型號： AM79C970
廠商： Advanced Micro Devices, Inc.
英文描述： PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus
中文描述： PCnetTM - PCI單芯片以太網控制器的PCI總線
文件頁數： 86/168頁
文件大?。?/td> 943K
代理商： AM79C970
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁
P R E L I M I N A R Y
AMD
1-953
Am79C970
longer than the time required to
send the maximum length frame.
BABL will be set if 1519 bytes or
greater are transmitted.
When BABL is set,
INTA
is as-
serted if IENA = 1 and the mask
bit BABLM in CSR3 is clear.
BABL assertion will set the ERR
bit.
BABL is set by the MAC layer and
cleared by writing a “1”. Writing a
“0” has no effect. BABL is cleared
by H_RESET or S_RESET or by
setting the STOP bit.
Collision Error indicates that the
collision inputs to the AUI port
failed to activate within 20 net-
work bit times after the chip ter-
minated
transmission
Test). This feature is a trans-
ceiver test feature.
In 10BASE-T mode, CERR will
be set after a transmission if the
T-MAU is in link fail state.
CERR assertion will not result in
an interrupt being generated.
CERR assertion will set the ERR
bit.
CERR is set by the MAC layer
and cleared by writing a “1”. Writ-
ing a “0” has no effect. CERR is
cleared by H_RESET or S_RE-
SET or by setting the STOP bit.
Missed Frame is set when
PCnet-PCI controller has lost an
incoming receive frame resulting
from a Receive Descriptor not
being available. This bit is the
only immediate indication that re-
ceive data has been lost since
there is no current receive de-
scriptor. Missed Frame Counter
(CSR112) also increments each
time a receive frame is missed.
When MISS is set,
INTA
is as-
serted if IENA = 1 and the mask
bit MISSM in CSR3 is clear.
MISS assertion will set the ERR
bit.
MISS is set by the Buffer Man-
agement Unit and cleared by
writing a “1”. Writing a “0” has no
effect. MISS is cleared by H_RE-
SET or S_RESET or by setting
the STOP bit.
Memory Error is set when PCnet-
PCI controller requests the use of
the system interface bus by as-
serting
REQ
and has not
13
CERR
(SQE
12
MISS
11
MERR
received
GNT
assertion after a
programmable length of time.
The length of time in microsec-
onds before MERR is asserted
will depend upon the setting of
the
Bus
Timeout
(CSR100). The default setting of
CSR100 will give a MERR after
51.2
microseconds
latency.
When MERR is set,
INTA
is as-
serted if IENA = 1 and the mask
bit MERRM in CSR3 is clear.
MERR assertion will set the ERR
bit, regardless of the settings of
IENA and MERRM.
MERR is set by the Bus Interface
Unit and cleared by writing a “1”.
Writing a “0” has no effect. MERR
is
cleared
by
S_RESET or by setting the
STOP bit.
Receive Interrupt. RINT is set by
the Buffer Management Unit of
the PCnet-PCI controller after
the last descriptor of a receive
packet has been updated by writ-
ing a ZERO to the ownership bit.
RINT may also be set when the
first descriptor of a receive pack-
et has been updated by writing a
ZERO to the ownership bit if the
SPRINTEN bit of CSR3 has been
set to a ONE.
When RINT is set,
INTA
is as-
serted if IENA = 1 and the mask
bit RINTM in CSR3 is clear.
RINT is cleared by the host by
writing a “1”. Writing a “0” has no
effect. RINT is cleared by
H_RESET, S_RESET or by set-
ting the STOP bit.
Transmit Interrupt is set after the
OWN bit in the last descriptor of a
transmit frame has been cleared
to indicate the frame has been
sent or an error occurred in the
transmission.
When TINT is set,
INTA
is as-
serted if IENA = 1 and the mask
bit TINTM in CSR3 is clear.
TINT is set by the Buffer Man-
agement Unit and cleared by
writing a “1”. Writing a “0” has no
effect. TINT is cleared by
H_RESET or S_RESET or by
setting the STOP bit.
Initialization Done indicates that
the initialization sequence has
Register
of
bus
H_RESET,
10
RINT
9
TINT
8
IDON
相關PDF資料
PDF描述
AM79C971VCW PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus
AM79C971 PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus
AM79C971KCW IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE
AM79C972BKCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BKIW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
相關代理商/技術參數
參數描述
AM79C970A 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
AM79C970AKC 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
AM79C970AKC\\W 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Advanced Micro Devices 功能描述:
AM79C970AKC\W 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*